Small Parts & Bearings - an MBA company

Rail Supports Without Shaft Categories


Shafting Precision Ground


Rail Supports - Without Shaft
Rail Supports - Without Shaft

Also see combined categories:
All Shaft Supports

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium.

Related Information:


Rail Supports - With Shaft
Rail Supports - With Shaft

Also see combined categories:
All Shaft Supports

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium.

Related Information:


Rail Supports - With Shaft - One Piece
Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Related Information:


Shafting - Pre Drilled and Tapped - High Carbon Steel
Shafting - Pre Drilled and Tapped - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.


Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings



You may also be interested in

Shafting Aluminium


Shafting - Supported - Pre-Drilled - Aluminium
Shafting - Supported - Pre-Drilled - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

For Drylin Bearings.

Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.


Shafting Precision Ground


Supports - Pedestal Two Bolt
Supports - Pedestal Two Bolt

Also see combined categories:
All Supports

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.

Related Information:


Rollers - Durasoft - Shaft Mount - Black Neoprene
Rollers - Durasoft - Shaft Mount - Black Neoprene

Also see combined categories:
All Shaft Mount Durasoft Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature.


Rollers - Durasoft - Shaft Mount - Coloured Urethane
Rollers - Durasoft - Shaft Mount - Coloured Urethane

Also see combined categories:
All Shaft Mount Durasoft Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. Blue colour may turn a shade of green when exposed to UV lighting.


Rollers - Solid - Shaft Mount - Black Neoprene
Rollers - Solid - Shaft Mount - Black Neoprene

Also see combined categories:
All Solid Shaft Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed.


Rollers - Solid - Shaft Mount - Coloured Urethane
Rollers - Solid - Shaft Mount - Coloured Urethane

Also see combined categories:
All Solid Shaft Mount Rollers

Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.

Designed for use in machines and assembly operations where part movement and protection is needed. Blue colour may turn a shade of green when exposed to UV lighting.


Collars - Threaded - Clamp Type - Steel
Collars - Threaded - Clamp Type - Steel

Also see combined categories:
All Threaded Shaft Collars

Offer full radial holding power without marring the shaft.



Collars - Threaded - Clamp Type - Stainless Steel
Collars - Threaded - Clamp Type - Stainless Steel

Also see combined categories:
All Threaded Shaft Collars

Offer full radial holding power without marring the shaft.



Knobs - Oval Tapered - Press On - Phenolic
Knobs - Oval Tapered - Press On - Phenolic

Also see combined categories:
All Knobs

Press on knobs hold on securely without threads or set screws

Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.


Dual Vee - Tracks without Mounting Holes - Steel
Dual Vee - Tracks without Mounting Holes - Steel

Also see combined categories:
All Dual Vee Tracks

Vee guide rails for vee grooved track roller guide wheels.

Match Track Size with same size Guide Wheel.

Related Information:


Dual Vee - Tracks without Mounting Holes - Stainless Steel
Dual Vee - Tracks without Mounting Holes - Stainless Steel

Also see combined categories:
All Dual Vee Tracks

Vee guide rails for vee grooved track roller guide wheels.

Match Track Size with same size Guide Wheel.

Related Information:


Bearings - One Way - Roller
Bearings - One Way - Roller

Also see combined categories:
All One Way Clutch Bearings

Roller Clutch Bearings rotate in one direction only.

Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.

Related Information:


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.


Snap Rings - External - Basic
Snap Rings - External - Basic

Also see combined categories:
All External Snaprings

Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.

Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment.


Couplings - Rigid - 2 Piece Clamp - Steel
Couplings - Rigid - 2 Piece Clamp - Steel

Also see combined categories:
All Rigid Couplings

12L14 Steel

Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.


Linear Slide - Drylin - Rail
Linear Slide - Drylin - Rail

Also see combined categories:
All Linear Slides

Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.

Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.

Related Information:


Drylin Linear Assembly Parts - Carriage Only
Drylin Linear Assembly Parts - Carriage Only

Also see combined categories:
All Drylin Assembly Parts

Linear sliding motion. Plain and Locking Types. These carriages require a matching guide rail or matching rack and pinion. Match by size.

Drylin(R) T linear guides are maintenance free and run without additional lubrication. Consequently, they are also suitable for use in damp or dirty environments. Available with a manually operated clamp to achieve a force fit at any desired point along the travel path. The wing screw is used to clamp the slide in place of the guide. Matching components listed in separate category.

Related Information:


Linear Slide - Drylin - Carriage Assembly
Linear Slide - Drylin - Carriage Assembly

Also see combined categories:
All Linear Slides

Insensitive to dust and dirt. Match with Drylin Rail sold seperately.

Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.

Related Information:


Linear Track System - Crowned Roller
Linear Track System - Crowned Roller


Rails, rollers and end stops sold separately. Please choose your components from the listing.

Easy to use system is usually mounted on a vertical surface as a low cost linear motion solution. Hardened crown roller allows for self-alignment with good strength and long life. Rails are unistrut typeand are black powder coated. End stops prevent over travel and come with a mounting bolt. End stops are not designed to support loads. Maximum bearing load is 130 kg. Maximum bearing speed is 45 mtrs per minute.


Ratchets - Without Hub
Ratchets - Without Hub


Match with pawls listed on this site.


Related Information:


Bearings - Pivot - Without Inner Ring
Bearings - Pivot - Without Inner Ring

Also see combined categories:
All Pivot Bearings

Note! Minimum quantities apply to production of these items.


Rollers - Track - Without Inner race
Rollers - Track - Without Inner race

Also see combined categories:
All Track Rollers


Related Information:




Plungers - Indexing - Cam Action - Without Hex Nut
Plungers - Indexing - Cam Action - Without Hex Nut

Also see combined categories:
All Indexing Plungers

Used in many tooling applications as well as on many types of machinery and equipment.

Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.

Related Information:


Plungers - Indexing - Grip - Stainless - Without Nut
Plungers - Indexing - Grip - Stainless - Without Nut

Also see combined categories:
All Indexing Plungers

Grip is held in a notch in the fully retracted position. In this position the locking pin does not project from the body at all.



Plungers - Indexing - Grip - Steel - Without Nut
Plungers - Indexing - Grip - Steel - Without Nut

Also see combined categories:
All Indexing Plungers

Grip is held in a notch in the fully retracted position. In this position the locking pin does not project from the body at all.



Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel
Plungers - Indexing - Non Locking - Without Knob - 303 Stainless Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

303 Stainless Steel.


Plungers - Indexing - Non Locking - Without Knob - Steel
Plungers - Indexing - Non Locking - Without Knob - Steel

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.


Plungers - Indexing - Precision - With Support - Ball Grip
Plungers - Indexing - Precision - With Support - Ball Grip

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.



Plungers - Indexing - Precision - With Support - Locking - Ball Grip
Plungers - Indexing - Precision - With Support - Locking - Ball Grip

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.



Adjusters - Rigid
Adjusters - Rigid

Also see combined categories:
All Mounting Feet

Adjustable supports for all kinds of machinery.

Mild steel bright zinc plated. Screwdriver cross recess in base. Use as mounting feet.

Related Information:


Adjusters - Tilt
Adjusters - Tilt

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Adjustable supports for all kinds of machinery. Mounting feet levelers.

Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25o from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.

Related Information:


Mounts - Pivotal Levelers - Base Without Stud
Mounts - Pivotal Levelers - Base Without Stud

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Tough bonded neoprene. Patented pivotal leveler keeps equipment level and dampens an average 85% of noise. Adjusters.

The mounting nut which holds the stud is molded into the pad in a steel bracket and rotates freely permitting at least 6.35mm of leveling. No stud included so you can use your own custom stud.


Plungers - Indexing - Unthreaded - Non Locking - Steel - Without Knob
Plungers - Indexing - Unthreaded - Non Locking - Steel - Without Knob

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

For use where the application calls for the plunger to be welded or bonded. Body and pin are steel with black oxide finish.


Plungers - Indexing - Non Locking - With Shoulder - Steel - Without Knob
Plungers - Indexing - Non Locking - With Shoulder - Steel - Without Knob

Also see combined categories:
All Indexing Plungers

Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.

Body and pin are steel with black oxide finish.


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.

Related Information:


Linear Slides - MiniVee - Carriages
Linear Slides - MiniVee - Carriages


Use with MiniVee tracks and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Steel wheel carriages support loads to 50kg whilst the polymer wheel carriages support loads to 6kg. Carriages and track sold separately.

Related Information:


Bearings - Ball - 4 Point Contact
Bearings - Ball - 4 Point Contact


4 Point Contact Bearings support Axial Loads in both directions. Can replace double row angular contact bearings where space is limited.

Related Information:


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Snap Rings - Internal - Basic
Snap Rings - Internal - Basic

Also see combined categories:
All Internal Snaprings

M2300 / SB / ESB Snaprings. Like an internal circlip without the lugs.

Applications include gear systems, securing needle bearings and to act as spacers. Used on the inside bore diameter of a housing or similar.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Linear Slides - MiniVee - Track - Hardened Steel
Linear Slides - MiniVee - Track - Hardened Steel


Use with MiniVee carriages and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.

Related Information:


Linear Slides - MiniVee - Track - Unhardened Steel
Linear Slides - MiniVee - Track - Unhardened Steel


Use with MiniVee carriages and support washers

Low profile miniature linear slide system ideal for semi-conductor, laboratory, medical and packaging applications. Non actuated MiniVee linear slide consists of one or more 6061-T6 anodised aluminium wheel carriages with Dual Vee integrated wheels. Double edged track from 165 to 927mm. Carriages and track sold separately.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.