Pulleys Vee
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at
Bushings - QD.
Related Information:
Stenco vee pulleys
Related Information:
Dual purpose pulleys suit A section and M section belts
Related Information:
Stenco vee pulleys
Related Information:
Dual purpose pulleys suit A section and M section belts
Related Information:
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.
Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at
Bushings - Snap - Closed.
Related Information:
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.
Also called a dome plug. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at
Bushings - Snap - Open.
Related Information:
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Use with QD bush to suit your bore requirement
Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height. This category may be available in the new MBA online store at
Pulleys - Poly V - J Section - QD Bush.
Related Information:
Used as spacers between pulleys, gears etc
Series DB100 Spirol
Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12. This category may be available in the new MBA online store at
Pins - Dowel Bushings.
Related Information:
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned. This category may be available in the new MBA online store at
Dual Vee - Adaptor Bushings.
Related Information:
Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub. This category may be available in the new MBA online store at
Reducers - Bore.
Related Information:
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined. This category may be available in the new MBA online store at
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core.
Related Information:
Vibration isolation for mobile and static applications involving plate clamping
Related Information:
Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.
Suitable for use with shaftloc sleeves.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With brass insert.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. No locking device.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Also known as LT. Moulded single or double flange. No locking device.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.
Related Information:
Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000. This category may be available in the new MBA online store at
Bushes - Aluminium Bronze - Flanged.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
Related Information:
Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.
Related Information:
Oil impregnated flanged sintered bronze bushes.
Related Information:
Oil impregnated sintered bronze bushes.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.