Small Parts & Bearings - an MBA company

Pulleys U Groove Idler Plastic With Plain Bore Categories


Pulleys Grooved


Pulleys - U Groove - Idler - Plastic - With Plain Bore
Pulleys - U Groove - Idler - Plastic - With Plain Bore

Also see combined categories:
All U Groove Bearings and Pulleys
All Idler Pulleys

Plastic and Steel with Steel Ball Bearings or Plain Bearings.

Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Plastic - With Plain Bore.

Related Information:


Pulleys - U Groove - Idler - Plastic - With Ball Bearing
Pulleys - U Groove - Idler - Plastic - With Ball Bearing

Also see combined categories:
All U Groove Bearings and Pulleys
All Idler Pulleys

Plastic and Steel with Steel Ball Bearings or Plain Bearings.

Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Plastic - With Ball Bearing.

Related Information:


Pulleys - U Groove - Idler - Steel - With Bearing
Pulleys - U Groove - Idler - Steel - With Bearing

Also see combined categories:
All U Groove Bearings and Pulleys
All Idler Pulleys

Steel with Steel Ball Bearings

Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Steel - With Bearing.

Related Information:


Pulleys - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide - Plastic - Plain
Pulleys - Timing -  2.073mm Pitch - 40DP - 6.4mm Wide - Plastic - Plain

Also see combined categories:
All 40DP 2.073mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Also known as LT. Moulded single or double flange. No locking device.


Related Information:


Pulleys - Timing - 3.000mm Pitch - GT - 9mm Wide - Plastic - Plain
Pulleys - Timing -  3.000mm Pitch - GT -  9mm Wide - Plastic - Plain

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide. No locking device. Use with GT2 or GT3 type belts.

Use with GT2 or GT3 type belts. This category may be available in the new MBA online store at Pulleys - Timing - 3.000mm Pitch - GT - 9mm Wide - Plastic - Plain.

Related Information:


Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Plain
Pulleys - Timing -  5.000mm Pitch - HTD - 9mm Wide - Plastic - Plain

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. No locking device.

This category may be available in the new MBA online store at Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Plain.

Related Information:


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Plain
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Plain

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. No locking device.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - Idler
Pulleys - Timing - Idler

Also see combined categories:
All Idler Pulleys

Complete with Needle Roller Bearing.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. This category may be available in the new MBA online store at Pulleys - Timing - Idler.

Related Information:


Pulleys - Timing - 2.000mm Pitch - GT - 6mm Wide - Plastic - Insert
Pulleys - Timing -  2.000mm Pitch - GT - 6mm Wide - Plastic - Insert

Also see combined categories:
All 2mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide. Brass insert. Use with GT2 or GT3 type belts.

Use with GT2 or GT3 type belts. This category may be available in the new MBA online store at Pulleys - Timing - 2.000mm Pitch - GT - 6mm Wide - Plastic - Insert.

Related Information:


Pulleys - Timing - 3.000mm Pitch - GT - 9mm Wide - Plastic - Insert
Pulleys - Timing -  3.000mm Pitch - GT -  9mm Wide - Plastic - Insert

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide. Brass insert. Use with GT2 or GT3 type belts.

Use with GT2 or GT3 type belts.

Related Information:


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.

Suitable for use with shaftloc sleeves.

Related Information:


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Insert
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Insert

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Brass insert.


Related Information:


Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub
Pulleys - Timing -  5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Fairloc locking hub.


Related Information:


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Insert
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Insert

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With brass insert.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Plastic - Insert
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Plastic - Insert

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Brass insert.


Related Information:


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic - Plain.


Bearings - Conveyor - Hex Bore - Plastic - Double Row
Bearings - Conveyor - Hex Bore - Plastic - Double Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Double Row.


Bearings - Conveyor - Hex Bore - Plastic - Single Row
Bearings - Conveyor - Hex Bore - Plastic - Single Row

Also see combined categories:
All Conveyor Bearings

Plastic hex bore conveyor bearings with 316 stainless balls

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Plastic - Single Row.


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Tensioner - Adjustable Screw
Tensioner - Adjustable Screw

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.

Idler shaft and pulleys not included with tensioner. This category may be available in the new MBA online store at Tensioner - Adjustable Screw.

Related Information:


Sprockets - 3.12 x 1.47mm - Simplex - Plastic
Sprockets -  3.12 x 1.47mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.12mm miniature plastic chain. This category may be available in the new MBA online store at Sprockets - 3.12 x 1.47mm - Simplex - Plastic.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain. This category may be available in the new MBA online store at Sprockets - 3.75 x 1.6mm - Simplex - Plastic.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Plastic
Sprockets -  6.35 x 2.8mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 6.35mm plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch. This category may be available in the new MBA online store at Sprockets - 6.35 x 2.8mm - Simplex - Plastic.

Related Information:


Sprockets - 9.53 x 4.7mm - Simplex - Plastic
Sprockets -  9.53 x 4.7mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 9.53x4.7mm plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 4.7mm - Simplex - Plastic.

Related Information:


Sprockets - 9.53 x 5.7mm - Simplex - Plastic
Sprockets -  9.53 x 5.7mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 9.53x5.7mm steel chain (06B BS). British Standard 06B - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 5.7mm - Simplex - Plastic.

Related Information:


Tensioner - Drive - Adjustable Angle
Tensioner - Drive - Adjustable Angle

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.

Idler shaft and pulleys not included with tensioner. This category may be available in the new MBA online store at Tensioner - Drive - Adjustable Angle.

Related Information:


Tensioner - Drive - Adjustable Flanged
Tensioner - Drive - Adjustable Flanged

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened. This category may be available in the new MBA online store at Tensioner - Drive - Adjustable Flanged.

Related Information:


Universal Joints - Telescoping - Plastic - Brass Spider and Insert
Universal Joints - Telescoping - Plastic - Brass Spider and Insert

Also see combined categories:
All Universal Joints
All Telescoping Universals

Acetal plastic telescoping universal joints with nickle plated brass spiders and bore inserts



Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Double Row.


Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row
Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row

Also see combined categories:
All Conveyor Bearings

316 stainless conveyor bearings with plastic cage and plastic hex insert

Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Stainless Steel - Single Row.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.