Small Parts & Bearings - an MBA company

Searched For: Pulleys Poly V J Section Qd Bush Categories


Pulleys - Poly V - J Section - QD Bush
Pulleys - Poly V - J Section - QD Bush


Use with QD bush to suit your bore requirement

Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height. This category may be available in the new MBA online store at Pulleys - Poly V - J Section - QD Bush.

Related Information:


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at Bushings - QD.

Related Information:


Pulleys - Poly V - J Section - Through Bored
Pulleys - Poly V - J Section - Through Bored


Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height. This category may be available in the new MBA online store at Pulleys - Poly V - J Section - Through Bored.

Related Information:


Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

This category may be available in the new MBA online store at Pulleys - Vee - A - 4L - Single Row - For QD Bushing.

Related Information:


Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

This category may be available in the new MBA online store at Pulleys - Vee - B - 5L - Single Row - For QD Bushing.

Related Information:


Pulleys - Geared - Hobby
Pulleys - Geared - Hobby

Also see combined categories:
All Flat Belt Pulleys

Small UPE grooved pulleys suitable for driving small o'rings or rubber bands. O-rings should be less than 2mm section diameter.

This category may be available in the new MBA online store at Pulleys - Geared - Hobby.


Belts - Poly V - J Section
Belts - Poly V - J Section


Belts include a tensile cord, most suited for industrial or adjustable applications

Poly Vee are ideal for high ratio and high speed drives. J Section polyvee is 2.34mm pitch and 3.56mm belt height. Note, this series is not a strechable type of belt. The belt width wll be determined by the number of ribs x the pitch. This category may be available in the new MBA online store at Belts - Poly V - J Section.

Related Information:


Bushes - Plastic - Clip - Bevelled Edge
Bushes - Plastic - Clip - Bevelled Edge

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. This category may be available in the new MBA online store at Bushes - Plastic - Clip - Bevelled Edge.

Related Information:


Bushes - Steel - DU - Split - Flanged
Bushes - Steel - DU - Split - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.

Operating Temperature -200o to 280o Celsuis. Maximum Load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.

Related Information:


Bushes - Steel - DU - Split - Unflanged
Bushes - Steel - DU - Split - Unflanged

Also see combined categories:
All Steel Bushes
All Unflanged Steel Bushes

Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.

Cast Iron and Steel. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 12.7mm Wide - Taperlock
Pulleys - Timing -  9.525mm Pitch - L -  12.7mm Wide - Taperlock

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.

Black oxide coated steel or cast iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 9.525mm Pitch - L - 12.7mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Taperlock
Pulleys - Timing -  9.525mm Pitch - L -  19.1mm Wide - Taperlock

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.

Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 25.4mm Wide - Taperlock
Pulleys - Timing -  9.525mm Pitch - L -  25.4mm Wide - Taperlock

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts. Taperlock bush required for bore.

Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 9.525mm Pitch - L - 25.4mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock.

Related Information:


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Closed.

Related Information:


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber. This category may be available in the new MBA online store at Bushings - Snap - Open.

Related Information:


Bushes - Aluminium Bronze - Flanged
Bushes - Aluminium Bronze - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000. This category may be available in the new MBA online store at Bushes - Aluminium Bronze - Flanged.

Related Information:


Bushes - Aluminium Bronze - Graphite Plug - Flanged
Bushes - Aluminium Bronze - Graphite Plug - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000. This category may be available in the new MBA online store at Bushes - Aluminium Bronze - Graphite Plug - Flanged.

Related Information:


Bushes - Aluminium Bronze - Graphite Plug - Unflanged
Bushes - Aluminium Bronze - Graphite Plug - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000. This category may be available in the new MBA online store at Bushes - Aluminium Bronze - Graphite Plug - Unflanged.

Related Information:


Bushes - Aluminium Bronze - Unflanged
Bushes - Aluminium Bronze - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000. This category may be available in the new MBA online store at Bushes - Aluminium Bronze - Unflanged.

Related Information:


Bushes - Brass - Graphite Plug - Flanged
Bushes - Brass - Graphite Plug - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

High-Tensile Brass Alloy. Suitable for use under conditions of heavy load and low speed operation. Solid Lubricant Plugs. Excellent wear resistance can be exerted at parts with reciprocating motion, frequent starting and stopping, etc., where oil film is difficult to form. Class 7 precision ID. 29N per mm sq max allowable load with max allowable speed 0.5m per second unlubricated and 1m per second lubricated.

Related Information:


Bushes - Brass - Graphite Plug - Unflanged
Bushes - Brass - Graphite Plug - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

High-Tensile Brass Alloy. Suitable for use under conditions of heavy load and low speed operation. Solid Lubricant Plugs. Excellent wear resistance can be exerted at parts with reciprocating motion, frequent starting and stopping, etc., where oil film is difficult to form. Class 7 precision ID. 29N per mm sq max allowable load with max allowable speed 0.5m per second unlubricated and 1m per second lubricated.

Related Information:


Bushes - Bronze - Sintered - Flanged
Bushes - Bronze - Sintered - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Oil impregnated flanged sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM. This category may be available in the new MBA online store at Bushes - Bronze - Sintered - Flanged.

Related Information:


Bushes - Bronze - Sintered - Unflanged
Bushes - Bronze - Sintered - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Oil impregnated sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM. This category may be available in the new MBA online store at Bushes - Bronze - Sintered - Unflanged.

Related Information:


Bushes - Bronze - Solid
Bushes - Bronze - Solid

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Solid precision leaded gunmetal bronze bushes. C93200 as indicated in the listings.

Composition (Approx.) : Copper 81%, Tin 7%, Zinc 4%, Lead 6%, Nickel 2%. Hardness : 70-90 BHN. This category may be available in the new MBA online store at Bushes - Bronze - Solid.

Related Information:


Bushes - Bronze - Spherical - Sintered
Bushes - Bronze - Spherical - Sintered

Also see combined categories:
All Bronze Bushes

Spherical OD Oil Impregnated Sintered Bronze Bushes.

ID and OD oversized. Enquire if details required. This category may be available in the new MBA online store at Bushes - Bronze - Spherical - Sintered.

Related Information:


Bushes - Plastic - Acetal - Oil Impregnated
Bushes - Plastic - Acetal - Oil Impregnated

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Oil impregnated acetal with self-lubricating characteristics.

This category may be available in the new MBA online store at Bushes - Plastic - Acetal - Oil Impregnated.

Related Information:


Bushes - Plastic - Clip - Double Flanged
Bushes - Plastic - Clip - Double Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For use with sheet metal. Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F). This category may be available in the new MBA online store at Bushes - Plastic - Clip - Double Flanged.

Related Information:


Bushes - Plastic - Ertalyte TX - Unflanged
Bushes - Plastic - Ertalyte TX - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Self lubricated, high mechanical strength, stiffness and hardness.

This category may be available in the new MBA online store at Bushes - Plastic - Ertalyte TX - Unflanged.

Related Information:


Bushes - Plastic - Rulon J - Flanged
Bushes - Plastic - Rulon J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range. This category may be available in the new MBA online store at Bushes - Plastic - Rulon J - Flanged.

Related Information:


Bushes - Plastic - Rulon J - Unflanged
Bushes - Plastic - Rulon J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range. This category may be available in the new MBA online store at Bushes - Plastic - Rulon J - Unflanged.

Related Information:


Bushes - Stainless Steel and PTFE - Flanged
Bushes - Stainless Steel and PTFE - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.

Related Information:





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.