Delays on shipments from USA and shipments passing through Singapore
Shipments from the USA are currently experiencing delays due to severe weather conditions. Shipments passing through Singapore are experiencing some minor delays due to Covid restrictions. We will keep you updated if your orders are affected.
Pulleys Geared Hobby Categories
Pulleys Grooved
Pulleys - Geared - Hobby
Small UPE grooved pulleys suitable for driving small o'rings or rubber bands. O-rings should be less than 2mm section diameter.
You may also like to check if Hobby and Engineering Supplies list a range of Pulleys - Geared - Hobby.
Gear Blanks
You may also be interested in
Spacers
Tolerance Rings
Rings - Tolerance
Tolerance rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
Shafting Precision Ground
Shafting - Ground - Precision - Titanium - Ti-Gr5 - TC4
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
Pulley Blocks
Pulleys - Blocks - Eye - Swivel
Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.
Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.
Pulleys Grooved
Pulleys - U Groove - Idler - Plastic - With Ball Bearing
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings.
Related Information:
Pulleys - U Groove - Idler - Plastic - With Plain Bore
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings.
Related Information:
Pulleys - U Groove - Idler - Steel - With Bearing
Steel with Steel Ball Bearings
Use with round belts such as Rounthane or O-Rings.
Related Information:
Pulleys Idler
Pulleys - Timing - Idler
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
Related Information:
Pulleys Poly Vee
Pulleys - Poly V - J Section - QD Bush
Use with QD bush to suit your bore requirement
Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height.
Related Information:
Pulleys - Poly V - J Section - Through Bored
Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height.
Related Information:
Pulleys Vee
Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Pulleys - Vee - A - 4L - Single Row - Through Bore - Aluminium
Stenco vee pulleys
Related Information:
Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron
Dual purpose pulleys suit A section and M section belts
To determine the pitch diameter for M section deduct 8.636mm (0.34 inch) from the pitch diameter listed.
Related Information:
Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Pulleys - Vee - M - 3L - Single Row - Through Bore - Aluminium
Stenco vee pulleys
Related Information:
Pulleys - Vee - M - 3L - Single Row - Through Bore - Cast Iron
Dual purpose pulleys suit A section and M section belts
To determine the pitch diameter for A section add 8.636mm (0.34 inch) to the pitch diameter listed.
Related Information:
Pulleys Timing 40DP LT Pitch
Pulleys - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide - Through Bore
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 4.7 to 4.8mm wide. Also known as LT.
Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide - Plastic - Plain
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Also known as LT. Moulded single or double flange. No locking device.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide - Through Bore
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 7.9 to 8.0mm wide. Also known as LT.
Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Also known as LT.
Related Information:
Pulleys Timing AT10 10mm
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Pulleys - Timing - 10.000mm Pitch - AT10 - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing AT5 5mm
Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
Pulleys - Timing - 5.000mm Pitch - AT5 - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
HTD 5mm series Flanges can be used with this stock.
Related Information:
Pulleys Timing GT2 -14mm
Pulleys - Timing - 14.000mm Pitch - GT2 - 115mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 115mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 170mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 170mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 40mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 40mm wide. Taperlock
Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 55mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 55mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 85mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 85mm wide. Taperlock
Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.
Related Information:
Pulleys Timing GT2 2mm
Pulleys - Timing - 2.000mm Pitch - GT2 - 3mm Wide - Through Bore
Timing Pulleys to suit GT 2mm Pitch Timing Belts.
Aluminium Alloy. Finished Bores with Set Screws.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - EZ-Lock
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.
Aluminium Alloy. EZI-LOK Hub Clamps together wit a Socket Head Cap Screw. Socket Cap Screw is Supplied with Pulley.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - Plastic - Insert
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide. Brass insert.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - Plastic - Plain
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide. No locking device.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - Through Bore
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.
Aluminium Alloy. Set Screw and EZI-LOK Hubs.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - 9mm Wide - Through Bore
Timing Pulleys to suit 2mm Pitch GT Timing Belts 9mm Wide.
Aluminium Alloy. Set Screw Locking.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - STOCK - 304 Stainless
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys - Timing - 2.000mm Pitch - GT2 - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing GT2 3mm
Pulleys - Timing - 3.000mm Pitch - GT2 - 15mm Wide - Through Bore
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 15mm Wide.
Aluminium Alloy. Finsihed through bore. Set screw locking.
Related Information:
Pulleys - Timing - 3.000mm Pitch - GT2 - 6mm Wide - Through Bore
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 6mm Wide.
Aluminium Alloy. Finished through bore ready to assemble.
Related Information:
Pulleys - Timing - 3.000mm Pitch - GT2 - 9mm Wide - EZ-Lock
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide.
Aluminium Alloy. EZ-Lock hub clamps to the shaft with a socket head cap screw. Cap screw is supplied with the pulley.
Related Information:
Pulleys - Timing - 3.000mm Pitch - GT2 - 9mm Wide - Plastic - Insert
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide. Brass insert.
Related Information:
Pulleys - Timing - 3.000mm Pitch - GT2 - 9mm Wide - Plastic - Plain
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide. No locking device.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127000 products in 2359 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
