Small Parts & Bearings - an MBA company

Protective Packing And Sleeves Categories


Sleeving - Mesh
Sleeving - Mesh


Low cost protection for threaded and cylindrical parts

Elastic snug tight fit protective sleeve fits over straight, tapered or contoured parts. Made from polyethylene. Thickness of web approx 1.8mm. Sold per foot (300mm). Maximum contunuous roll is 100 feet (30 mtrs).


Screws - Thumb - Knurled - Brass
Screws - Thumb - Knurled  - Brass

Also see combined categories:
All Thumb Screws

Brass knurled head thumb screws with zinc or black oxide protective coating.

This category may be available in the new MBA online store at Screws - Thumb - Knurled - Brass.

Related Information:


Bearings - One Way - Sprag - Standard
Bearings - One Way - Sprag - Standard

Also see combined categories:
All One Way Clutch Bearings

Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.

Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.

Related Information:


Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.

This category may be available in the new MBA online store at Sleeves - Hex Hole - Carbon Steel.


Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.

This category may be available in the new MBA online store at Sleeves - Hex Hole - Hardened.


Sleeves - Square Hole - Plain - Carbon Steel
Sleeves - Square Hole - Plain - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.

This category may be available in the new MBA online store at Sleeves - Square Hole - Plain - Carbon Steel.


Sleeves - Square Hole - Plain - Hardened
Sleeves - Square Hole - Plain - Hardened

Also see combined categories:
All Square Hole Sleeves

Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.

This category may be available in the new MBA online store at Sleeves - Square Hole - Plain - Hardened.


Sleeves - Square Hole - Threaded - Carbon Steel
Sleeves - Square Hole - Threaded - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.

This category may be available in the new MBA online store at Sleeves - Square Hole - Threaded - Carbon Steel.


Shaftloc-tm Sleeves - Single Ended
Shaftloc-tm Sleeves - Single Ended

Also see combined categories:
All Shaftloc

Simple effective way to lock components onto shafts.

416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened. This category may be available in the new MBA online store at Shaftloc-tm Sleeves - Single Ended.

Related Information:


Attachments - Cable - Loop Sleeves
Attachments - Cable - Loop Sleeves


Use with synchromesh or standard miniature cable

This category may be available in the new MBA online store at Attachments - Cable - Loop Sleeves.

Related Information:


Attachments - Cable - Stop Sleeves
Attachments - Cable - Stop Sleeves


Use with synchromesh or standard miniature cable. Use a swaging tool to compress the stop sleeve over the end of the cable.

This category may be available in the new MBA online store at Attachments - Cable - Stop Sleeves.

Related Information:


Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only


Match with hubs from hubs category

This category may be available in the new MBA online store at Couplings - Geargrip - Precision - Sleeves Only.

Related Information:


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Bearings - Needle Roller - Inner Rings
Bearings - Needle Roller - Inner Rings


Hardened sleeves for needle roller bearings.

This category may be available in the new MBA online store at Bearings - Needle Roller - Inner Rings.

Related Information:


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only


Match with sleeves from sleeves category

This category may be available in the new MBA online store at Couplings - Geargrip - Precision - Hubs Only.

Related Information:


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Ballscrew - Nook Series - Flanges
Ballscrew - Nook Series - Flanges


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish. This category may be available in the new MBA online store at Ballscrew - Nook Series - Flanges.


Ballscrew - Nook Series - Right Hand
Ballscrew - Nook Series - Right Hand


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm. This category may be available in the new MBA online store at Ballscrew - Nook Series - Right Hand.


Rollers - Urethane - Lengths
Rollers - Urethane - Lengths

Also see combined categories:
All Tyred OD Bearings
All Rollers

Low cost alternative for making your own wheels, castors, rollers, sheaves etc. Urethane rod with dual hardness. Harder inner sleeve with softer outside for use as a roller.

Blue outer tyre 90A Durometer bonded to a hard brown 75D Durometer inner sleeve. This results in a hard anti friction bearing surface inside with a soft tyre outside. The roller can be cut and machined to suit your purposes. Testing for your application is recommended. This category may be available in the new MBA online store at Rollers - Urethane - Lengths.

Related Information:


Plungers - Ball - Push Fit - 303 Stainless Steel
Plungers - Ball - Push Fit - 303 Stainless Steel

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


Plungers - Ball - Push Fit - Plastic Body - Plastic Ball
Plungers - Ball - Push Fit - Plastic Body - Plastic Ball

Also see combined categories:
All Push Fit Ball Plungers

Unthreaded. Plastic body and ball.

Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.

Suitable for use with shaftloc sleeves.

Related Information:


Collars - Shaft - Gripfast - ABS Plastic
Collars - Shaft - Gripfast - ABS Plastic

Also see combined categories:
All Round Bore Shaft Collars

Self Locking - Quick Release.

265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. This category may be available in the new MBA online store at Collars - Shaft - Gripfast - ABS Plastic.

Related Information:


Housings - Bearing - Tapped Base - Thermoplastic with Chrome Steel Bearing
Housings - Bearing - Tapped Base - Thermoplastic with Chrome Steel Bearing


Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.


Housings - Bearing - 2 Bolt Flange - Thermoplastic with Chrome Steel Bearing
Housings - Bearing - 2 Bolt Flange - Thermoplastic with Chrome Steel Bearing


Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.


Inserts - Rivet Nuts - Klik - Threadsert
Inserts - Rivet Nuts - Klik - Threadsert

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.


Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing
Housings - Bearing - Tapped Base - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food grade.


Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - Bearing - 2 Bolt Flange - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.

Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form McMaster Carr Cross Reference PDF Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 135332 products in 2017 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 135332 products in 2017 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.