Pins General
For holding, clamping and positioning work pieces. Body is black oxide steel.
Steel ball and elasticised spring with black oxide coated steel body.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Plastic ball and stainless spring with black oxide coated steel body.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Stainless ball and stainless spring with black oxide coated steel body.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Steel ball and elasticised spring with black oxide coated steel body.
Related Information:
Used for locking the ends of timing belt lengths used in linear applications
Suits single sided belts only. Aluminium. Screws, hex nuts and washers included.
Related Information:
Bronze double sided medals displaying emblem and motto on one side and aircraft or ship on the other.
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
Related Information:
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
GT2 Series Metric Timing Belts.
Pitch (P) - 3.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. Breaking strength is not indicative of working strength.
Related Information:
GT2 Series Metric Timing Belts Double Sided
Pitch (P) - 3.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. Breaking strength is not indicative of working strength.
Related Information:
GT2 Series Metric Timing Belts Double Sided
Pitch (P) - 3.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. Breaking strength is not indicative of working strength.
Related Information:
GT2 Series Metric Timing Belts Double Sided
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 5.00mm. Breaking strength is not indicative of working strength.
Related Information:
GT2 Series Metric Timing Belts Double Sided
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.93mm. Belt Height (W) - 5.00mm. Breaking strength is not indicative of working strength.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Pitch (P) - 3.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. Breaking strength is not indicative of working strength.
Related Information:
HTD Series Metric Timing Belts.
Pitch (P) - 3.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 2.41mm. Breaking strength is not indicative of working strength.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Breaking strength is not indicative of working strength.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Breaking strength is not indicative of working strength.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as internal hitch pins, bridge pins or humpback pins
Also known as internal hitch pins, bridge pins or humpback pins
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
Effective way to position heavy loadsquickly and easily. Single pin unit offers high rigidity with small deflection.
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics.
Related Information:
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.
Related Information:
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
3 Piece Thrust Bearings Banded Type
Related Information:
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Carbon Steel Washers are hardened to RC59.61.
Related Information:
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42.
Related Information:
Washers and Rollers sold separately. Match cage and roller assembly with washers from the washers category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Related Information:
Washers and Rollers sold separately. Match washers with cage and roller assembly from the cage and roller assembly category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125482
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.