Pins General
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
GT2 and GT3 Series Metric Timing Belts Double Sided
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.22mm. Belt Height (W) - 3.20mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 3.000mm.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Pitch (P) - 5.000mm. This category may be available in the new MBA online store at
Belts - Timing - 5.000mm Pitch - HTD Double Sided - 15mm Wide.
Related Information:
HTD Series Metric Timing Belts Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.08mm. Belt Height (W) - 5.30mm. Pitch (P) - 5.000mm. This category may be available in the new MBA online store at
Belts - Timing - 5.000mm Pitch - HTD Double Sided - 9mm Wide.
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Used for locking the ends of timing belt lengths used in reciprocating applications
Suits single and double sided belts. Black Polycarbonate with 303 stainless fasteners. Low inertia. Compact Design. Patent Pending. For MXL, XL, GT 2mm, GT 3mm, GT 5mm, HTD 3mm and HTD 5mm belt pitches.
Related Information:
17-4 PH or PH15-7MO stainless steel spindle and shank. Self locking and positive locking. All components made from stainless steel.
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Also known as internal hitch pins, bridge pins or humpback pins
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - Chrome Steel.
Related Information:
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - Stainless Steel.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Flat - Chrome Steel.
Related Information:
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Flat - Stainless Steel.
Related Information:
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic.
Related Information:
Quick release. Commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed.
Economical. Positive lock detent pins. Aluminium handles. 360 Brass Buttons. 304 Stainless Steel Shank and balls. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Quick release. Stainless steel commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed. Tee handle.
Economical. Positive lock detent pins. Aluminium handles. 304 Stainless Steel Shank. 360 Brass Button. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200
o to 280
o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. This category may be available in the new MBA online store at
Washers - Thrust - DP4 Type.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating. This category may be available in the new MBA online store at
Snap Buttons - Double End.
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
3 Piece Thrust Bearings Banded Type
Related Information:
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Related Information:
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Related Information:
Washers sold separately. Match cage and roller assembly with washers from the washers category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Related Information:
Caged Rollers sold separately. Match these washers with cage and roller assembly from the cage and roller assembly category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Related Information:
Rust proof nickel plated made from finest quality zinc aluminium alloy
Damps low frequency vibrations. Vibration dampening
Double Row Ball Bearings - Angular Contact.
Related Information:
Double Row Ball Bearings - Angular Contact.
Related Information:
Related Information:
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Double Row - with Glass Balls.
Related Information:
Precision made. Column lock feature. Will not become loose when adjusting. Universal design will fit any make of magnetic base, surface gauge or indicator. 12L14 Steel.
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40
oC to 80
oC (minus 40 Deg F to 176 Deg F). This category may be available in the new MBA online store at
Bushes - Plastic - Clip - Double Flanged.
Related Information:
Used for deburring and smoothing metals.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.