Small Parts & Bearings - an MBA company

Packing Boxes And Materials Categories


Packing Materials
Packing Materials


A small selection of common packing materials. Boxes, markers, mailpacks, bubble wrap and magicseal bags.



Books - Engineering
Books - Engineering

Also see combined categories:
All Books

Machinery handbook contains standards, materials and other general engineering information.

Engineers Black Book, Fasteners Black Book, Machinery Handbook, Shop Reference.


Couplings - Helical - Short - Ondrives
Couplings - Helical - Short - Ondrives

Also see combined categories:
All Helical and Slit Couplings

Material: 303 S3U Stainless.

Related Information:


Bushes - Steel - DU - Split - Flanged
Bushes - Steel - DU - Split - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.

Operating Temperature -200o to 280o Celsuis. Maximum Load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.

Related Information:


Bushes - Steel - DU - Split - Unflanged
Bushes - Steel - DU - Split - Unflanged

Also see combined categories:
All Steel Bushes
All Unflanged Steel Bushes

Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.

Related Information:


Washers - Spring - Curved - Carbon Steel
Washers - Spring - Curved - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions.


Washers - Spring - Curved - Stainless Steel
Washers - Spring - Curved - Stainless Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions.


Clutches - Slip - Inline
Clutches - Slip - Inline

Also see combined categories:
All Slip Clutches

Multiplate Design.

Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.

Related Information:


Balls - Plastic - PVC
Balls - Plastic -  PVC

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.

Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.

Related Information:


Bearings - Press-Fit - Acetal - SDP
Bearings - Press-Fit - Acetal - SDP

Also see combined categories:
All Press In Bearings

Press fit installation. Do not press bearing against insert. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 oC. Carbon steel outer. Self aligning to +/- 5o. Use any shaft material with 0.4 um or finer finish.

Related Information:


Magnets - Ceramic Blocks
Magnets - Ceramic Blocks

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Magnets - Ceramic Cylinder
Magnets - Ceramic Cylinder

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Washers - Spring - 2 Wave Type - Zinc Plated
Washers - Spring - 2 Wave Type - Zinc Plated

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.



Nuts - Blind
Nuts - Blind

Also see combined categories:
All Nuts

Blind nuts - Tee nuts.

Put steel threads in soft materials like wood without counterboring.


Latches - Slam Action - Slide
Latches - Slam Action - Slide


Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.



Springs - Neoprene
Springs - Neoprene

Also see combined categories:
All Rubber Springs

Neoprene elastomer springs have proven to be the safest, most efficient material for punching, stamping and drawing dies.

Major advantages include high loads, increased durability, better performance, no maintenance and long life.

Related Information:


Leadscrew Nut Flanges for Acme Supernuts
Leadscrew Nut Flanges for Acme Supernuts

Also see combined categories:
All Leadscrew Nut Flanges

Flanges for Acme leadscrew thread supernuts metric and imperial

MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.

Related Information:


Nuts - Hexagonal - Weld - Steel
Nuts - Hexagonal - Weld - Steel

Also see combined categories:
All Lock Nuts

Used in metalwork or for leveling appliances. Round or slab base. Material thickness is the thickness of the flange.



Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2.

Related Information:


Leadscrew Nuts - Metric - Flanged - Plastic
Leadscrew Nuts - Metric - Flanged - Plastic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Iglidur W300. Single Start / Right Hand.

Related Information:


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Leadscrew Nuts - Metric - Round - Plastic - Iglidur W300
Leadscrew Nuts - Metric - Round - Plastic - Iglidur W300

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Iglidur W300 Plastic. Single Start / Right Hand.

Related Information:


Sleeving - Mesh
Sleeving - Mesh


Low cost protection for threaded and cylindrical parts

Elastic snug tight fit protective sleeve fits over straight, tapered or contoured parts. Made from polyethylene. Thickness of web approx 1.8mm. Sold per foot (300mm). Maximum contunuous roll is 100 feet (30 mtrs).


Balls - Plastic - Bored
Balls - Plastic - Bored

Also see combined categories:
All Plastic Balls - Bored

Bored acetal balls as used in plastic rod ends.

Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.

Related Information:


Redi-Rail - Rail
Redi-Rail - Rail


Match carriage and rail by rail widh

Easy to use systemcan be iunstalled into many applications including packaging, material handling, automation and assembly equipment. A complete unit consists of a roller guide and rail (sold separately). The roller guide is made from 6061-T6 aluminium base with 3 rollers. Rollers made from 52100 hardened steel, lubricated and sealed. Rail made from 6061-T6 aluminium with hardened and ground steel raceways for the rollers to run on.

Related Information:


Shafting - Pipe - Aluminium
Shafting - Pipe - Aluminium

Also see combined categories:
All Pipe Shaft
All Metal Tube

Recommended for use with Igubal Drylin bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and Less than 9.


Redi-Rail - Roller Guides
Redi-Rail - Roller Guides


Match carriage and rail by rail widh

Easy to use systemcan be iunstalled into many applications including packaging, material handling, automation and assembly equipment. A complete unit consists of a roller guide and rail (sold separately). The roller guide is made from 6061-T6 aluminium base with 3 rollers. Rollers made from 52100 hardened steel, lubricated and sealed. Rail made from 6061-T6 aluminium with hardened and ground steel raceways for the rollers to run on.

Related Information:


Magnets - Rare Earth - Plated
Magnets - Rare Earth - Plated

Also see combined categories:
All Magnets
All Rare Earth Magnets

Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.

High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 oC to 93 oC. Size tolerances +/- 0.13.


Shafting - Aluminium
Shafting - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.


Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:


Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:


Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit
Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit

Also see combined categories:
All Magnets
All Ceramic Magnets

Extended poles can be lightly machined. Press fit. Insulated aluminium casing.

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Belts - Rounthane
Belts - Rounthane


Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).

Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length. FDA / USDA approved.

Related Information:


Bearings - SDP - PTFE Filled Acetal - Flange Mounted
Bearings - SDP - PTFE Filled Acetal - Flange Mounted

Also see combined categories:
All Press In Bearings

Retainer : Carbon Steel Black Oxide Finish. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 oC. Self lubricating. Use any shaft material with 0.4 um or finer finish. Soft or hard shafting is OK.

Related Information:


Shafting - Supported - Pre-Drilled - Aluminium
Shafting - Supported - Pre-Drilled - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

For Drylin Bearings.

Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: Ph Greater than 2 and less than 9.


Ball Transfer Units - Screw Stem - Stainless - Precision
Ball Transfer Units - Screw Stem - Stainless - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Drylin Linear Assembly Parts - Guide Rails Only
Drylin Linear Assembly Parts - Guide Rails Only

Also see combined categories:
All Drylin Assembly Parts

These rails require a matching carriage as listed in a separate category. Match by size.

Slide Rail: Extruded Aluminium Construction Material: Al Mg Si 0.5. Coating: Hard anodised, 50um Hardness: 500HV. Matching components listed in separate category.

Related Information:


Balsa Wood - Dowel
Balsa Wood - Dowel


Round section dowel. Delivery Surcharges May Apply on Selected Items

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.

Related Information:


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Inserts - Rivet Nuts - Klik - Ribbed
Inserts - Rivet Nuts - Klik - Ribbed

Also see combined categories:
All Klik Rivet Nuts

Individual Inserts for use with the Klik Thread Setter Tool

These blind threaded inserts offer strong torque and pull out characteristics. Especially effective in sheet metal and other thin material. Insert is placed into the hole in the parent material and crimped up with the installation tool. Installs from one side - no tapping required. Installs almost flush eliminating the need for countersinking. Made from plated steel.

Related Information:


Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole
Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole

Also see combined categories:
All Magnets
All Ceramic Magnets

Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Balsa Wood - Block
Balsa Wood - Block


Rectangular and square section short lengths. Delivery Surcharges May Apply on Selected Items

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.


Balsa Wood - Leading Edge
Balsa Wood - Leading Edge


Leading edge for aircraft use. Delivery Surcharges May Apply on Selected Items

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.

Related Information:


Balsa Wood - Trailing Edge
Balsa Wood - Trailing Edge


Trailing edge for aircraft use. Delivery Surcharges May Apply on Selected Items

This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.

Related Information:


Bearings - Press-Fit - Sintered Bronze - Flange Mounted - SDP
Bearings - Press-Fit - Sintered Bronze - Flange Mounted - SDP

Also see combined categories:
All Press In Bearings

Porous sintered bronze bearing. -28 to 95 oC. Retainer : Carbon Steel / Zinc Plated or Oxycote(R) Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.

Related Information:


Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core
Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core

Also see combined categories:
All Posi-Drive Belts

Same as US 20 Pitch - Use with Posi-Drive Sprockets.

Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.

Related Information:


Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core

Also see combined categories:
All Posi-Drive Belts

Same as US 20 Pitch - Use with Posi-Drive Pulleys.

Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.

Related Information:


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.