Small Parts & Bearings - an MBA company

Motors Dc 6mm Diameter Categories


Motors DC


Motors - DC 6mm Diameter
Motors - DC  6mm Diameter

Also see combined categories:
All DC Motors

Our smallest motors at an affordable price.

Various models 10000 to 30000 rpm. Low starting voltage of Less than0.8V. Rated Voltage 1.3V. Less than 43 dB Mechanical Noise Level. 100 hours / 100000 turns mechanical life. Clockwise rotation when viewed from shaft end. Not recommended for reversing.

Related Information:


You may also be interested in

Gearmotors DC


Gearmotors - DC - Size 25 Low Cost
Gearmotors - DC - Size  25 Low Cost


25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible

D Shaped 4x8mm Output Shaft.


Gearmotors Basic


Gearmotors - Basic - Hobby - 12.1mm Diameter
Gearmotors - Basic - Hobby - 12.1mm Diameter

Also see combined categories:
All Basic Gearmotors

Small light weight geared motors used in toys and small solar applications

NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.


Spring Motors


Spring Motors - RINO
Spring Motors - RINO

Also see combined categories:
All Spring Motors

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.


Spring Motors - SDP
Spring Motors - SDP

Also see combined categories:
All Spring Motors

301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.


Gearmotors DC


Gearmotors - DC - Size 12
Gearmotors - DC - Size  12

Also see combined categories:
All DC Gearmotors

12mm Gearhead Body Diameter.



Rod - Round - Urethane
Rod - Round - Urethane

Also see combined categories:
All Non Metallic Rod - Round

Hard urethane rubber compound. Machinable.

Length +/- 3.2mm. Diameter +/- 2 percent.

Related Information:


Rod - Round - Nylon
Rod - Round - Nylon

Also see combined categories:
All Plastic Rod

High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Rod - Round - PTFE
Rod - Round - PTFE

Also see combined categories:
All Plastic Rod

Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Rod - Round - Polyester PETP
Rod - Round - Polyester PETP

Also see combined categories:
All Plastic Rod

High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Posi Drive Stage - Ball Slide
Posi Drive Stage - Ball Slide

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Posi Drive Stage - Crossed Roller
Posi Drive Stage - Crossed Roller

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Rod - Round - Acetal
Rod - Round - Acetal

Also see combined categories:
All Plastic Rod

Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Switches - Rocker
Switches - Rocker

Also see combined categories:
All Switches

20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.

Switchs are rated at 10amp @ 600VAC with finger safe screw terminals.


Rollers - Feed - With Aluminium Sleeve
Rollers - Feed - With Aluminium Sleeve

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Related Information:


Couplings - Reli-a-flex - Long Series - Clamp Type
Couplings - Reli-a-flex - Long Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Couplings - Reli-a-flex - Short Series - Clamp Type
Couplings - Reli-a-flex - Short Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Rod - Round - Sintered Bronze
Rod - Round - Sintered Bronze

Also see combined categories:
All Metal Rod - Round

Sintered bronze rod is supplied oversized so it can be machine finished to the dimensions shown.

Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.

Related Information:


Rollers - Drive
Rollers - Drive

Also see combined categories:
All Rollers

Neoprene 60 durometer black ground outside diameter drive rollers



Motors - DC 12.0X30.0 mm
Motors - DC 12.0X30.0 mm

Also see combined categories:
All DC Motors

6.0V - 22800 RPM


Related Information:


Motors - DC 16.6X32.0 mm
Motors - DC 16.6X32.0 mm

Also see combined categories:
All DC Motors

M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 18.9X18.0X9.5 mm
Motors - DC 18.9X18.0X9.5 mm

Also see combined categories:
All DC Motors

M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.

Related Information:


Motors - DC 20.0X25.0 mm
Motors - DC 20.0X25.0 mm

Also see combined categories:
All DC Motors

1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts


Related Information:


Motors - DC 22.4X38.0 mm
Motors - DC 22.4X38.0 mm

Also see combined categories:
All DC Motors


Related Information:


Motors - DC 23.8X30.6 mm
Motors - DC 23.8X30.6 mm

Also see combined categories:
All DC Motors

12 VDC - 12,300 RPM unloaded at 4.5 volts


Related Information:


Motors - DC 24.3X12.35 mm
Motors - DC 24.3X12.35 mm

Also see combined categories:
All DC Motors

6.0 VDC - 4,900 RPM unloaded at 4.5 volts


Related Information:


Motors - DC 25.0x20.1X15.1 mm
Motors - DC 25.0x20.1X15.1 mm

Also see combined categories:
All DC Motors

M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 25.0X21.0 mm
Motors - DC 25.0X21.0 mm

Also see combined categories:
All DC Motors

M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 26.9X23.8 mm
Motors - DC 26.9X23.8 mm

Also see combined categories:
All DC Motors

M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 26.9X24.2X18.3 mm
Motors - DC 26.9X24.2X18.3 mm

Also see combined categories:
All DC Motors

MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM. Standard 130 Size Hobby Motor.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 30.5X24.2 mm
Motors - DC 30.5X24.2 mm

Also see combined categories:
All DC Motors

M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 30.5X24.2X18.3 mm
Motors - DC 30.5X24.2X18.3 mm

Also see combined categories:
All DC Motors

MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 36.0X71.0 mm
Motors - DC 36.0X71.0 mm

Also see combined categories:
All DC Motors

High power, high speed 11,800 RPM unloaded at 12 volts


Related Information:


Motors - DC 8.0X10.0 mm
Motors - DC 8.0X10.0 mm

Also see combined categories:
All DC Motors

3.5V - 20500 RPM


Related Information:


Bearings - Spherical OD
Bearings - Spherical OD


Bearings with a spherical outside diameter.

Combined listing of spherical OD track rollers and bearings for Linear Guide systems.

Related Information:


Bearings - One Way - Roller
Bearings - One Way - Roller

Also see combined categories:
All One Way Clutch Bearings

Roller Clutch Bearings rotate in one direction only.

Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.

Related Information:


Knobs - Oval Tapered - Press On - Phenolic
Knobs - Oval Tapered - Press On - Phenolic

Also see combined categories:
All Knobs

Press on knobs hold on securely without threads or set screws

Shaft diameter should be +0.000 / - 0.076 mm for best performance. Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs. Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.


Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:


Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:


Gears - Spur - 120DP - Hub Mounting - Aluminium
Gears - Spur - 120DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 120DP - Hub Mounting - Stainless
Gears - Spur - 120DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - Hub Mounting - Aluminium
Gears - Spur -  24DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - Hub Mounting - Stainless
Gears - Spur -  24DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - Hub Mounting - Aluminium
Gears - Spur -  32DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - Hub Mounting - Stainless
Gears - Spur -  32DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - Hub Mounting - Aluminium
Gears - Spur -  48DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - Hub Mounting - Stainless
Gears - Spur -  48DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 64DP - Hub Mounting - Aluminium
Gears - Spur -  64DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 64DP - Hub Mounting - Stainless
Gears - Spur -  64DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.