Magnets Alnico
Cast Alnico 5 bar
Supplied with keeper
General purpose horseshoe magnet
Supplied with keeper
Alnico sintered ASA 8HC
Related Information:
Extended poles can be lightly machined. Press fit. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
No keepers
Supplied with keeper
No keepers
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Ideal for hanging signs and lights, retrieving steel items from tanks, vats, bins etc.
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73
oC to 93
oC. Size tolerances +/- 0.13. This category may be available in the new MBA online store at
Magnets - Rare Earth - Plated.
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures. This category may be available in the new MBA online store at
Magnets - Rare Earth - Shielded.
Magnetic Vinyl Sheets and Magnetic Rubber Strip
Permanent Magnet.
Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.
Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. This category may be available in the new MBA online store at
Clutches - Slip - Magnetic Particle - No Power.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless - Side Holes.
Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.
Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed. This category may be available in the new MBA online store at
Pulleys - Blocks - Eye - Swivel.
Requires no power.
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
3 Piece Thrust Bearings Open Type. Excellent performance in electrical and magnetism sensitive applications. Full ceramic silicon nitride.
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at
Bearings - Thrust - Ball - Grooved - ZRO2 Ceramic.
Related Information:
Used for shallow drawers, tool chests and medical carts.
Hold in detent. Full extension. 12.7mm Side Space. Includes 32mm hole pattern as well as traditional hole pattern.
Used for filing cabinets, utility and industrial truck storage, machine tool drawers, generators and heavy mechanical devices.
Lever Disconnect. Non locking. 19.1mm side space.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Various styles - refer pictures
Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.
Related Information:
Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.
Related Information:
Ultrafast Responses.
The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start. This category may be available in the new MBA online store at
Clutches - Magnetic Particle 24VDC.
Related Information:
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Used for shallow drawers, tool chests and medical carts.
Used for shallow drawers, tool chests and medical carts.
Used for shallow drawers, tool chests and medical carts.
Used for handling large work in drill presses or band saw machines.
Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet. This category may be available in the new MBA online store at
Parallels - Ball.
Chamfered edge bearings for Linear Guide Systems and pushbikes
Often used in pushbike headsets. Note bearings for pushbikes with two chamfered edges have the chamfer on the inner ring on one side and outer ring on the other - designation CEP. This category may be available in the new MBA online store at
Bearings - Chamfered Edges.
Related Information:
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.