Small Parts & Bearings - an MBA company

Leadscrews Metric Rolled Thread Carbon Steel Categories


Leadscrews


Leadscrews - Metric - Rolled Thread - Carbon Steel
Leadscrews - Metric - Rolled Thread - Carbon Steel

Also see combined categories:
All Metric Leadscrews

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Carbon Steel C35. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Related Information:


Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:


Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:


Leadscrew Nuts - Metric - Flanged - Plastic
Leadscrew Nuts - Metric - Flanged - Plastic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Iglidur W300. Single Start / Right Hand.

Related Information:


Leadscrew Nuts - Metric - Round - Plastic - Iglidur W300
Leadscrew Nuts - Metric - Round - Plastic - Iglidur W300

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Iglidur W300 Plastic. Single Start / Right Hand.

Related Information:


Leadscrew Nut Flanges for Acme Supernuts
Leadscrew Nut Flanges for Acme Supernuts

Also see combined categories:
All Leadscrew Nut Flanges

Flanges for Acme leadscrew thread supernuts metric and imperial

MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.

Related Information:


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


Hexagonal Bar - Titanium Ti-Gr2 - Rolled
Hexagonal Bar - Titanium Ti-Gr2 - Rolled

Also see combined categories:
All Metal Bar - Hexagonal

Cold rolled hex bar to ASTM B348

Saw Cut Ends.


Shim and Foil - Steel
Shim and Foil - Steel

Also see combined categories:
All Shim
All Sheet

Precision shim sheet. Cold rolled steel. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.

Related Information:


Hexagonal Bar - Titanium Ti-Gr2 - Drawn
Hexagonal Bar - Titanium Ti-Gr2 - Drawn

Also see combined categories:
All Metal Bar - Hexagonal

Cold rolled and hot drawn hex bar to ASTM B348

Saw Cut Ends.


Bolts - Eye - Bent Rod - Steel
Bolts - Eye - Bent Rod - Steel

Also see combined categories:
All Eye Bolts

Not recommended for lifting.

Carbon steel zinc plated. Complete with nut. Rolled threads.


Leadscrews - Imperial - Acme - Alloy Steel
Leadscrews - Imperial - Acme - Alloy Steel

Also see combined categories:
All Imperial Leadscrews

Acme Leadscrew Thread - Use with Acme Supernuts

Alloy steel heat treated to RC 56-60.

Related Information:


Leadscrews - Imperial - Acme - Stainless Steel 18.8
Leadscrews - Imperial - Acme - Stainless Steel 18.8

Also see combined categories:
All Imperial Leadscrews

Acme Leadscrew Thread - Use with Acme Supernuts


Related Information:


Leadscrew Nut Flanges for Acme Nuts
Leadscrew Nut Flanges for Acme Nuts

Also see combined categories:
All Leadscrew Nut Flanges

Flanges for Acme leadscrew thread nuts imperial

These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.

Related Information:


Leadscrew Nuts - Imperial - Acme - Bronze
Leadscrew Nuts - Imperial - Acme - Bronze

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting

Nut only. Match with appropriate leadscrew.

Related Information:


Leadscrew Nuts - Imperial - Acme - Plastic
Leadscrew Nuts - Imperial - Acme - Plastic

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting


Related Information:


Leadscrew Nuts - Imperial - Supernuts - Acme
Leadscrew Nuts - Imperial - Supernuts - Acme

Also see combined categories:
All Leadscrew Nuts
All Imperial Leadscrew Nuts

Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting


Related Information:


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.

Related Information:


Bolts - Eye - Bent - Stainless Steel
Bolts - Eye - Bent - Stainless Steel

Also see combined categories:
All Eye Bolts

Not recommended for lifting. 304 stainless steel.

Complete with nut. Rolled threads.


Mounts - Centre Bolt - Solo Unitised
Mounts - Centre Bolt - Solo Unitised

Also see combined categories:
All Centrebolt Mounts

Vibration dampening

Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.




Pulleys - Blocks - Eye - Swivel
Pulleys - Blocks - Eye - Swivel

Also see combined categories:
All Pulley Blocks

Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Pulleys - Blocks - Flat
Pulleys - Blocks - Flat

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Pulleys - Blocks - Eye - Fixed
Pulleys - Blocks - Eye - Fixed

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Posi Drive Stage - Crossed Roller
Posi Drive Stage - Crossed Roller

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Mounts - Vibration - Isolation - Cup Style 2
Mounts - Vibration - Isolation - Cup Style 2

Also see combined categories:
All Cup Mounts

Industrial cupmounts provide excellent protection against severe impact shock, vibration and noise.

High vibration dampening. Fail safe, rugged interlocking metal and neoprene construction. Metal cupmount is cold rolled steel. Low profile compact design. Metal top plate is domed shape to guard against oil contamination. High grade neoprene elastomer provides resistance to ozone and oils.


Posi Drive Stage - Ball Slide
Posi Drive Stage - Ball Slide

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50

Metric Sizes to DIN 1.

Related Information:


Pins - Taper - Metric - Extractable - Internal Thread
Pins - Taper - Metric - Extractable - Internal Thread

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50 and threaded internally for easy extraction.

DIN 7978. Mild Steel.

Related Information:


Studs - Threaded - Standard
Studs - Threaded - Standard


Metric and imperial sizes. Steel and 303 stainless steel.

Yield strength 100,000 PSI. Tensile strength 125,000 PSI.


Gear Racks - Module 0.5 - Steel
Gear Racks - Module 0.5 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.8 - Steel
Gear Racks - Module 0.8 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 1.5 - Steel
Gear Racks - Module 1.5 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon Steel.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 1 - Steel
Gear Racks - Module 1 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon Steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 2.5 - Steel
Gear Racks - Module 2.5 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 2 - Steel
Gear Racks - Module 2 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 3 - Steel
Gear Racks - Module 3 - Steel

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gears - Mitre - Module 0.6 - Steel
Gears - Mitre - Module 0.6 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Mitre - Module 1.5 - Steel
Gears - Mitre - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Mitre - Module 2.5 - Steel
Gears - Mitre - Module 2.5 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Mitre - Module 2.75 - Steel
Gears - Mitre - Module 2.75 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Mitre - Module 2 - Steel
Gears - Mitre - Module 2 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle. Carbon steel.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Mitre - Module 3 - Steel
Gears - Mitre - Module 3 - Steel

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:


Gears - Spur - Module 0.4 - Steel
Gears - Spur - Module 0.4 - Steel

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Steel
Gears - Spur - Module 0.5 - Steel

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Steel
Gears - Spur - Module 0.8 - Steel

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1.5 - Steel
Gears - Spur - Module 1.5 - Steel

Also see combined categories:
All Module 1.5 Spur Gears
All Metal Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. AISI4135 carbon steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1 - Steel
Gears - Spur - Module 1 - Steel

Also see combined categories:
All Module 1.0 Spur Gears
All Metal Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 2.5 - Steel
Gears - Spur - Module 2.5 - Steel

Also see combined categories:
All Module 2.5 Spur Gears
All Metal Module 2.5 Spur Gears

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. Carbon steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 2 - Steel
Gears - Spur - Module 2 - Steel

Also see combined categories:
All Module 2.0 Spur Gears
All Metal Module 2.0 Spur Gears

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. AISI4135 carbon steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124473 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.