Delays on shipments from USA and shipments passing through Singapore
Shipments from the USA are currently experiencing delays due to severe weather conditions. Shipments passing through Singapore are experiencing some minor delays due to Covid restrictions. We will keep you updated if your orders are affected.
Leads And Connectors Categories
Leads - Hobby
Adaptor leads for batteries, battery chargers, servos and receivers including Tamiya, Deans and Losi plugs.
Includes Deans and T Connectors.
You may also be interested in
Belts Rounthane
Yoke Ends
Yoke Ends - Blank
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards. Also see clevis joints.
Related Information:
Yoke Ends - Threaded
Linkage Connectors
Drop forged steel machined to SAE standards. Also see clevis joints.
Related Information:
Spacers - Hex - Threaded - Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Caps - End - Kite
End caps with string holes and grooves for kite rods.
Joiners and connectors suitable for rod and tubing as well as for kites.
Spacers - Hex - Threaded - 316 Stainless Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Spacers - Hex - Threaded - 303-304 Stainless Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Belts - Rounthane
Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).
Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot) of length. Orders for more than one length of 305mm will be supplied as a continuous length. FDA / USDA approved.
Related Information:
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Balsa Wood - Leading Edge
Leading edge for aircraft use. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm
Not for sale outside of Australia and New Zealand
Bushes - Bronze - Solid
Solid precision leaded gunmetal bronze bushes. Either LG2 (C83600A) or C93200 as indicated in the listings.
Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
Related Information:
Batteries - Accessories
Miscellaneous battery accessories - Lipo safety charge sacks - Balancers - Leads - Battery Monitors - Etc
Related Information:
Bushes - Stainless Steel and PTFE - Flanged
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
Bushes - Stainless Steel and PTFE - Unflanged
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
Bushes - Steel - DU - Split - Flanged
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsuis. Maximum Load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Bushes - Steel - DU - Split - Unflanged
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Worm Gears - Module 0.8 Series 2 - Plastic Gear and Metallic Worm
Match with metallic worms Module 0.80 Series 2.
20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms - 24DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms - 32DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms - 64DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 24DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 24DP Series 1 - Plastic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 32DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 32DP Series 1 - Plastic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 32DP Series 2 - Plastic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - 48DP Series 1 - Metallic
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 3.35o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Ballscrew - Nook Series - Right Hand
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.
Balsa Wood - Dowel
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
Posi Drive Stage - Ball Slide
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
Posi Drive Stage - Crossed Roller
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
Balsa Wood - Trailing Edge
Trailing edge for aircraft use. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
Balsa Wood - Square
Square section in longer lengths 900mm plus. See block for short lengths. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
Leadscrew Nut Flanges for Acme Nuts
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.
Related Information:
Leadscrew Nut Flanges for Acme Supernuts
Flanges for Acme leadscrew thread supernuts metric and imperial
MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.
Related Information:
Leadscrew Nuts - Imperial - Acme - Bronze
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Nut only. Match with appropriate leadscrew.
Related Information:
Leadscrew Nuts - Imperial - Acme - Plastic
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Leadscrew Nuts - Imperial - Supernuts - Acme
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Leadscrew Nuts - Metric - Flanged - Plastic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
Related Information:
Leadscrew Nuts - Metric - Round - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
Related Information:
Leadscrew Nuts - Metric - Round - Plastic - Iglidur W300
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300 Plastic. Single Start / Right Hand.
Related Information:
Leadscrew Nuts - Metric - Square - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
Related Information:
Leadscrews - Imperial - Acme - Alloy Steel
Acme Leadscrew Thread - Use with Acme Supernuts
Alloy steel heat treated to RC 56-60.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127000 products in 2359 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
