Small Parts & Bearings - an MBA company

Latches Rotary Action Categories


Latches - Rotary Action - Link Lock - Keepers
Latches - Rotary Action - Link Lock - Keepers


Required for link lock rotary action latches. Match keeper with correct latch from selection.



Latches - Rotary Action - Link Lock - Rivetted - Stainless
Latches - Rotary Action - Link Lock - Rivetted - Stainless


Lift and rotate wing to operate.

Keepers not included and must be purchased separately.

Related Information:


You may also be interested in

Latches Slam Action


Latches - Slam Action - Slide
Latches - Slam Action - Slide


Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.



Catches - Rotary
Catches - Rotary


Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.



Latches - 1-4 Turn - Simple
Latches - 1-4 Turn - Simple


With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.

The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Latches - 1-4 Turn -Tee Handle - Non Locking
Latches - 1-4 Turn -Tee Handle - Non Locking

Also see combined categories:
All Quarter Turn Latches

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Catches - Straight Loop
Catches - Straight Loop


High strength overcentre catch and strike. Economical and compact. Available in plain steel, zinc plated or 304 stainless steel. With or without mounting holes. Strike is included. Dimensions are as mounted.

Tension can be increased by increasing distance between catch and strike.


Latches - Compression - Lift and Turn - Straight Handle
Latches - Compression - Lift and Turn - Straight Handle


Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.

Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.


Latches - Draw - Over Centre - 300 Grade Stainless Steel
Latches - Draw - Over Centre - 300 Grade Stainless Steel


Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.

Keepers included. Type SC-97533 has a hole for a padlock.


Latches - Draw - T-Handle - Stainless Steel
Latches - Draw - T-Handle - Stainless Steel


Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.



Latches - 110 Series - Adjustable Grip
Latches - 110 Series - Adjustable Grip


Ultimate strength 145kg. Working strength 120kg.

Strike needs to be ordered separately.


Latches - 200 Series - Heavy Duty
Latches - 200 Series - Heavy Duty


Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.


Tools - Rotary Files - Aluminium Cut
Tools - Rotary Files - Aluminium Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel.


Tools - Rotary Files - Double Cut
Tools - Rotary Files - Double Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel.


Tools - Rotary Files - Standard Cut
Tools - Rotary Files - Standard Cut

Also see combined categories:
All Tools

Used for deburring and smoothing metals.

Made from Heat treated steel.


Dampers - Rotary - 2.0 to 3.0 Ncm
Dampers - Rotary -  2.0 to 3.0 Ncm

Also see combined categories:
All Dampers

Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.

Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC.


Dampers - Rotary - 5.0 to 15.0 Ncm
Dampers - Rotary -  5.0 to 15.0 Ncm

Also see combined categories:
All Dampers

Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.

Body: Polycarbonate / Gear: Polyacetal. Fluid: Silicone. Temp range 0 to 50 oC.


Dampers - Rotary - 50 to 400 Ncm
Dampers - Rotary - 50 to 400 Ncm

Also see combined categories:
All Dampers

Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.

Body: Polycarbonate. Temp range 0 to 50 oC. Weight: Max 120 grams.


Handles - Tee
Handles - Tee


Zinc plated steel 7.94mm (5/16in.) square shank.



Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:


Handles - Latching - Padlocking
Handles - Latching - Padlocking


Zinc finished iron/steel construction. Has 5/16in. Square shank.



Plungers - Indexing - Cam Action Mounting Blocks
Plungers - Indexing - Cam Action Mounting Blocks


Used with cam action indexing plungers

Mounting blocks are made from steel with black oxide finish.

Related Information:


Plungers - Indexing - Cam Action - With Hex Nut
Plungers - Indexing - Cam Action - With Hex Nut

Also see combined categories:
All Indexing Plungers

Used in many tooling applications as well as on many types of machinery and equipment.

Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.

Related Information:


Plungers - Indexing - Cam Action - Without Hex Nut
Plungers - Indexing - Cam Action - Without Hex Nut

Also see combined categories:
All Indexing Plungers

Used in many tooling applications as well as on many types of machinery and equipment.

Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.

Related Information:


Handles - Latching - Cab Locks
Handles - Latching - Cab Locks


Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.



Strikes - Toggle Latch - Steel
Strikes - Toggle Latch - Steel


Used with toggle latches series 800, 802, 803 and 806



Handles - Latching - L-Handle - Locking
Handles - Latching - L-Handle - Locking


Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.


Related Information:


Handles - Latching - T-Handle - Folding
Handles - Latching - T-Handle - Folding

Also see combined categories:
All T Handles

Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.



Handles - Latching - T-Handle - Locking
Handles - Latching - T-Handle - Locking

Also see combined categories:
All T Handles

90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.


Related Information:


Strikes - Toggle Latch - Stainless Steel
Strikes - Toggle Latch - Stainless Steel


Used with toggle latches series 800, 802, 803 and 806



Latching Handles - Outside Door - Heavy Duty
Latching Handles - Outside Door - Heavy Duty


Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.



Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


Nuts - Hexagonal - Binx - Steel
Nuts - Hexagonal - Binx - Steel

Also see combined categories:
All Lock Nuts

The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.


Rings - Hoist - Side Pull - Full Swivel
Rings - Hoist - Side Pull - Full Swivel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Extra large diameter ring allows for large hook. Made of alloy steel with black oxide finish. Safety factor of 5 to 1.

Individually pull tested and certified.


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of alloy steel with black oxide finish. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of 316 stainless steel. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:


Nuts - Hexagonal - Binx - Stainless Steel 304
Nuts - Hexagonal - Binx - Stainless Steel 304

Also see combined categories:
All Lock Nuts

Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.


Catches - Snap In Style - Grabber -tm-
Catches - Snap In Style - Grabber -tm-


Fast economical installation.

Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.


Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force
Bumpers - Elastomer - Medium Energy Absorption - Low Reaction Force

Also see combined categories:
All Elastomer Bumpers

Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.

10 greater durability than rubber and 500 times greater than steel coiled springs. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62 oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included.


Magnets - Rare Earth - Plated
Magnets - Rare Earth - Plated

Also see combined categories:
All Magnets
All Rare Earth Magnets

Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.

High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 oC to 93 oC. Size tolerances +/- 0.13.


Belts - Vee - 15.9 x 9.5mm - 5L
Belts - Vee - 15.9 x 9.5mm - 5L

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

15.9mm Top Width x 9.5mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:


Catches - Compression Spring
Catches - Compression Spring


Three internal compression springs supply up to 30kg of spring tension. Available as padlockable or with secondary catch.

Spring tension compensates for gasket set. Provides exact tension for water tight and air tight seals.


Catches - Draw Pull
Catches - Draw Pull


Draw pull catches are available in either steel or 304 stainless. Strike is included.



Catches - Knuckle
Catches - Knuckle


Strong and light polyacetal and polyamide. Holds cabinets secure with 7kg of pull force.



Catches - Magnetic - Screw On
Catches - Magnetic - Screw On


Various styles - refer pictures



Catches - Magnetic - Ultra Thin - Heavy Duty
Catches - Magnetic - Ultra Thin - Heavy Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.


Related Information:


Catches - Magnetic - Ultra Thin - Light Duty
Catches - Magnetic - Ultra Thin - Light Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.


Related Information:


Catches - Roller
Catches - Roller


304 Stainless Steel and Polyurethane



Catches - Side Mount - Grabber -tm-
Catches - Side Mount - Grabber -tm-


Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.



Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.