Latches Other Categories
Latches - 110 Series - Adjustable Grip
Ultimate strength 145kg. Working strength 120kg.
Strike needs to be ordered separately.
Latching Handles - Outside Door - Heavy Duty
Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.
Latches - 1-4 Turn - Simple
With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.
The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
Latches - 1-4 Turn -Tee Handle - Non Locking
Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.
Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
Latches - Compression - Lift and Turn - Straight Handle
Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.
Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.
Latches - Draw - Over Centre - 300 Grade Stainless Steel
Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.
Keepers included. Type SC-97533 has a hole for a padlock.
Latches - Draw - T-Handle - Stainless Steel
Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.
Latches - Rotary Action - Link Lock - Keepers
Required for link lock rotary action latches. Match keeper with correct latch from selection.
Latches - Rotary Action - Link Lock - Rivetted - Stainless
Lift and rotate wing to operate.
Keepers not included and must be purchased separately.
Related Information:
Latches - Slam Action - Slide
Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.
Handles - Latching - Cab Locks
Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.
Handles - Latching - L-Handle - Locking
Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.
Related Information:
Handles - Latching - T-Handle - Folding
Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.
Handles - Latching - T-Handle - Locking
90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.
Related Information:
Handles - Latching - 2-Point Locking Rod Kit
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
Couplings - BoWex - Junior
Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.
Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.
Related Information:
Couplings - Neo-Flex
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Books - Engineering
Machinery handbook contains standards, materials and other general engineering information.
Engineers Black Book, Fasteners Black Book, Machinery Handbook, Shop Reference.
Bungs - Rectangular
Plastic bungs fit inside rectangular tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
Bungs - Round
Plastic bungs fit inside round tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
Bungs - Square
Plastic bungs fit inside square tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
Nuts - Aerotight
Aerotight is a Registered Trademark and can only be applied to goods manufactured by the Premier Screw and Repetition Company Limited. Any company infringing the registered trade mark may be liable to legal proceedings. Aerotight nuts should not be used on damaged or interrupted threads. When assembled on the screw at least two threads should protrude through the Aerotight nut. Advantages: Will not work loose. No other locking device needed.
Tips - Round
Plastic tips fit over outside of tubing.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene. Tips may be supplied tapered or cylindrical depending on stock availability.
Wheels - Robotic - Motorised
Motorised wheels for robotic and other applications
See also tracks for robotic applications.
Screws - Button - Socket - Aluminium
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
Related Information:
Screws - Cap - Socket - Aluminium
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
Related Information:
Screws - Low Head - Socket - 316L Stainless
316L Stainless Steel. Other sizes available on request.
Hexagon socket cap head with low head. Safety improvements and compact size for equipment and devices. May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. All clean washed, preventing the inclusion of oil and foreign particles.
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Connectors - Edge - Kite
Edge connectors for kite rods and tubes. Can be used for other applications requiring an angled join of rod or tubing. Not a precision item.
Joiners and connectors suitable for rod and tubing as well as for kites.
Nuts - Hexagonal - Nylon Insert - Steel
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
Washers - Bevel
For use with eyebolts to correct taper when used on I beams and other structural applications. Bevelled 2 in 12 which is standard for flanges of I beams and channels.
Malleable iron with black finish.
Turntable - Lockable
Heavy duty turntables are ideal for swivel displays, welding tables, industrial assemblies and many other applications.
Similar to lazy susans but heavy duty.
Related Information:
Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
Tips - For Kite Rods
Plastic tips fit over outside of rods and tubes for kites and other uses.
Joiners and connectors suitable for rod and tubing as well as for kites.
Turntable - Non-Lockable
Heavy duty turntables are ideal for swivel displays, welding tables, industrial assemblies and many other applications.
Similar to lazy susans but heavy duty.
Related Information:
Bearings for Pool Equipment
Acetal bearings for spa jets and pool vacuum wheels
No lubrication required other than the water they are running in.
Related Information:
Shims - Slotted - Imperial Sizes
Precision stainless steel 300 series. Solves alignment and leveling problems on pumps, generators and other machinery. Tabs eliminate need to place hands under machinery. Conform to standard bolt and stud sizes.
Bushings - QD
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.
Related Information:
RC Spare Parts - Hobby Pro
Hobby Pro spare parts listed by description. Suits Mutilator, Matador, H5 and H6 and other 1/5th Scale Petrol Cars
Bearings - Thrust - Ball - Grooved - Chrome Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
Bearings - Thrust - Ball - Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Related Information:
Lanyards - Nylon
One piece moulded retainer designed for light duty retention.
Customer assembled loop is designed to be used with press lock rivets or other fasteners. Nylon 6/6 in UV stabilised black.
Bushings - Snap - Open
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.
Also called a dome plug. Also see grommets for a similar product made from rubber.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127063 products in 2368 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
