Small Parts & Bearings - an MBA company

Latches 1 4 Turn Simple Categories


Latches Quarter Turn


Latches - 1-4 Turn - Simple
Latches - 1-4 Turn - Simple


With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.

The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Latches - 1-4 Turn -Tee Handle - Non Locking
Latches - 1-4 Turn -Tee Handle - Non Locking

Also see combined categories:
All Quarter Turn Latches

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Catches - Straight Loop
Catches - Straight Loop


High strength overcentre catch and strike. Economical and compact. Available in plain steel, zinc plated or 304 stainless steel. With or without mounting holes. Strike is included. Dimensions are as mounted.

Tension can be increased by increasing distance between catch and strike.


Latches - Compression - Lift and Turn - Straight Handle
Latches - Compression - Lift and Turn - Straight Handle


Lift handle to relax compression and then turn to open. Handle and sleeve are die cast zinc with either polished chrome or black powder coat finish.

Comes with mounting hardware. Max working load 44kg. M5 mounting screws supplied. For panels thicker than 6.35mm a longer screw and lockwasher combination will be required.


Catches - Compression Spring
Catches - Compression Spring


Three internal compression springs supply up to 30kg of spring tension. Available as padlockable or with secondary catch.

Spring tension compensates for gasket set. Provides exact tension for water tight and air tight seals.


Catches - Draw Pull
Catches - Draw Pull


Draw pull catches are available in either steel or 304 stainless. Strike is included.



Catches - Knuckle
Catches - Knuckle


Strong and light polyacetal and polyamide. Holds cabinets secure with 7kg of pull force.



Catches - Magnetic - Screw On
Catches - Magnetic - Screw On


Various styles - refer pictures



Catches - Magnetic - Ultra Thin - Heavy Duty
Catches - Magnetic - Ultra Thin - Heavy Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.


Related Information:


Catches - Magnetic - Ultra Thin - Light Duty
Catches - Magnetic - Ultra Thin - Light Duty


Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.


Related Information:


Catches - Roller
Catches - Roller


304 Stainless Steel and Polyurethane



Catches - Rotary
Catches - Rotary


Polyacetal catch and strike with polyethylene rollers. Ideal in corrosive environments.



Catches - Side Mount - Grabber -tm-
Catches - Side Mount - Grabber -tm-


Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.



Catches - Side Mount - With Microswitch - Grabber -tm-
Catches - Side Mount - With Microswitch - Grabber -tm-


Mounts inside your enclosure. Installs either right or left side by inverting. Use 4 gauge screws or 1/8in (3.125mm) rivets to install.

Switch is designed to operate as an indicator light or form part of a non-safety related logic circuit.


Catches - Snap In Style - Grabber -tm-
Catches - Snap In Style - Grabber -tm-


Fast economical installation.

Fits frames from 1.1 to 7.1mm thick. Installation hole size 15mm x 39.9mm. Push to close and pull to open. Spring loaded over centre action. Corrosion resistant black ABS with 303 stainless steel spring.


Latches - Draw - Over Centre - 300 Grade Stainless Steel
Latches - Draw - Over Centre - 300 Grade Stainless Steel


Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.

Keepers included. Type SC-97533 has a hole for a padlock.


Latches - Draw - T-Handle - Stainless Steel
Latches - Draw - T-Handle - Stainless Steel


Black rubber T Handle with stainless steel bracket and keeper. Shipped assembled. Installs with 4.8mm rivets (3/16 in.) or 10 Gauge Screws. Can be welded. Keeper included.



Latches - 110 Series - Adjustable Grip
Latches - 110 Series - Adjustable Grip


Ultimate strength 145kg. Working strength 120kg.

Strike needs to be ordered separately.


Latches - 200 Series - Heavy Duty
Latches - 200 Series - Heavy Duty


Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.


Latches - Rotary Action - Link Lock - Keepers
Latches - Rotary Action - Link Lock - Keepers


Required for link lock rotary action latches. Match keeper with correct latch from selection.



Latches - Rotary Action - Link Lock - Rivetted - Stainless
Latches - Rotary Action - Link Lock - Rivetted - Stainless


Lift and rotate wing to operate.

Keepers not included and must be purchased separately.

Related Information:


Latches - Slam Action - Slide
Latches - Slam Action - Slide


Fast snap in installation. Made from non-corrosive materials, black ABS plastic and stainless steel spring. Push to close latching.



Clamps - Lorenz
Clamps - Lorenz


Patented quick clamp is ideal for door openings on bins, hoppers, tanks and manholes. T-Handle allows torque without tools. The one piece unit is made from highly polished 304 stainless steel.

Full 50.8mm adjustment. 180o pivot when disengaged leaving access doorway unobstructed. Will not loosen through vibration. Brackets supplied for easy installation.


Handles - Tee
Handles - Tee


Zinc plated steel 7.94mm (5/16in.) square shank.



Handles - Latching - Padlocking
Handles - Latching - Padlocking


Zinc finished iron/steel construction. Has 5/16in. Square shank.



Handles - Latching - Cab Locks
Handles - Latching - Cab Locks


Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.



Strikes - Toggle Latch - Steel
Strikes - Toggle Latch - Steel


Used with toggle latches series 800, 802, 803 and 806



Handles - Latching - L-Handle - Locking
Handles - Latching - L-Handle - Locking


Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.


Related Information:


Handles - Latching - T-Handle - Folding
Handles - Latching - T-Handle - Folding

Also see combined categories:
All T Handles

Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.



Handles - Latching - T-Handle - Locking
Handles - Latching - T-Handle - Locking

Also see combined categories:
All T Handles

90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.


Related Information:


Shaftloc-tm Sleeves - Single Ended
Shaftloc-tm Sleeves - Single Ended

Also see combined categories:
All Shaftloc

Simple effective way to lock components onto shafts.

416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.

Related Information:


Latching Handles - Outside Door - Heavy Duty
Latching Handles - Outside Door - Heavy Duty


Black Glass Filled Polyamide Bezel, catch and Plug. Brass Shaft. Zinc plated mild steel fixing.


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.



Locknuts - Stainless Insert
Locknuts - Stainless Insert


Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.

Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (Pí) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.

Related Information:


Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Screws - Thumb - Half Turn
Screws - Thumb - Half Turn

Also see combined categories:
All Thumb Screws



Screws - Thumb - 1-4 Turn
Screws - Thumb - 1-4 Turn

Also see combined categories:
All Thumb Screws



Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.



Knobs - Three Lobe - Safety - Male
Knobs - Three Lobe - Safety - Male

Also see combined categories:
All Lobe Knobs
All Knobs

Knob only turns when pressed downwards and turned simultaneously to avoid involuntary turning. Also see star knobs



Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.



Pulleys - Blocks - Eye - Swivel
Pulleys - Blocks - Eye - Swivel

Also see combined categories:
All Pulley Blocks

Steel side plates. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.


Pulleys - Blocks - Flat
Pulleys - Blocks - Flat

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Bearings - One Way - Sprag - Standard
Bearings - One Way - Sprag - Standard

Also see combined categories:
All One Way Clutch Bearings

Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.

Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.

Related Information:


Pulleys - Blocks - Eye - Fixed
Pulleys - Blocks - Eye - Fixed

Also see combined categories:
All Pulley Blocks

Steel side plates with drop forged hooks. Electroplated sheaves are turned from cold rolled bar stock.

Bearings made from bronze and steel, oil impregnated for self lubrication. Designed for high load and medium speed.


Switches - Rocker
Switches - Rocker

Also see combined categories:
All Switches

20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.

Switchs are rated at 10amp @ 600VAC with finger safe screw terminals.


Rings - Hoist - Side Pull - Full Swivel
Rings - Hoist - Side Pull - Full Swivel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Extra large diameter ring allows for large hook. Made of alloy steel with black oxide finish. Safety factor of 5 to 1.

Individually pull tested and certified.


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of alloy steel with black oxide finish. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:


Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel
Rings - Hoist - Tamper Resistant - Swivel Eybolts - Stainless Steel

Also see combined categories:
All Hoist Rings

Full swivel and pivot action allows you to flip and turn parts without unhooking. Made of 316 stainless steel. Tamper resistant design is ideal for permanent mounting on OEM applications or on moulds, dies and fixtures.

safety factor of 5 to 1. Installation tool sold separately.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124481 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124481 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.