Keys and Keysteel
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6884
Related Information:
You may also be interested in
Eyebolts
Hot galvanised finished steel with machine thread.
Any deviations such as angular lifts, shock loads, modifications of the basic forging etc will result in drastically reduced maximum loads.
Hot galvanised finished steel with machine thread.
Any deviations such as angular lifts, shock loads, modifications of the basic forging etc will result in drastically reduced maximum loads.
Balls Metallic
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Related Information:
Linear Slides
Match with carriage by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.
Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Rails are subjected to multiple straightening processes during and after grinding of the ball paths to ensure straight and accurate rails.
Related Information:
Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.
Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.
Related Information:
Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.
Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.
Related Information:
Keys and Keysteel
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6884
Related Information:
Ball Transfers
Single ball bearings units for conveyor systems
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Single ball bearings units for conveyor systems
Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.
Shafting General Purpose
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Keys and Keysteel
Plain carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Plain carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Plain carbon steel
Related Information:
Zinc plated carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. Zinc plating may be silver or yellow in colour.
Related Information:
Zinc plated carbon steel key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. Zinc plating may be silver or yellow in colour.
Related Information:
Chain and Sprockets Roller
Match with 9.53x4.7mm steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch.
Related Information:
Spacers
Used as spacers between pulleys, gears etc
Low carbon mild steel.
Universal Joints Single
Carbon Steel. With keyway. Maximum operating angle 25 to 45 degrees (refer tables).
Related Information:
Tools Threading
High Speed Steel Short Machine Flute Taps. starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
High Speed Steel (HSS) Short Machine taps.
Mounts Leveling
For leveling machine tools, electronic racks, benches etc on uneven surfaces. Adjusters.
Match with 12.70x6.38mm simplex chain (41-1 ASA)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 41-1 - 1/2 inch.
Related Information:
Match with 12.70x7.75mm duplex chain (08B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.
Related Information:
Match with 19.05x12.57mm simplex steel chain (60-1 ASA)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 60-1 - 3/4 inch.
Related Information:
Protects general metalworking processes equipment including punch presses, milling machines, lathes, mixers, injection moulding machines, grinders from shock and vibration. Adjusters.
Simplifies installation. 63.5mm of neoprene provides controlled deflections under load. High isolation efficiency for vibration and shock forces, and reduction of transmitted sound. Adjustable up to 12.7mm above loaded height by a few turns of the leveling bolt and tightening the checknut. Corrosion resistant outer housing provides high strength. Neoprene elastomer resists oil, grease, ozone and caustics. Zinc plated hardware resists rust. Hex head bolt and locknut finished with mounts. Height dimensions indicate free height of mount under no load.
Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.
C1010 steel types best suited to arbor shimming.
Related Information:
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
Related Information:
Hot galvanised carbon steel. Use with synchromesh or standard miniature cable
Meets USA Fed. Spec. FF-T-276b for Type III thimbles.
Related Information:
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
Related Information:
Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.
Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.
Related Information:
Plain carbon spring steel DIN1481.
Related Information:
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Carbon steel hand taps. Carbon Steel (CS) Hand taps.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Nickel Plated Steel. Adjusters.
Zinc plated carbon steel with steel nuts included
Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Plain carbon steel.
Related Information:
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated.
Related Information:
Metric Sizes Tapered 1:50
Metric Sizes to DIN 1.
Related Information:
Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093.
Wave Washers - All Materials.
ID and OD are long axis dimensions.
Carbon steel suitable for welding
Not for lifting.
Low carbon cold drawn steel with zinc plated finish
Any deviations such as angular lifts, shock loads, modifications will result in drastically reduced maximum loads.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Adjusters.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Adjusters.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Adjusters.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Adjusters.
15o swivel off centreline to adjust to uneven surfaces and level machine tools, electronic racks and benches. Adjusters.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125378
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.