Thread Inserts
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive - Flanged.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Threaded inserts are screwed into pre-formed or pre-drilled holes and cut their own threads. Perfect for permanent installations.
Made from brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Slotted Drive - Short.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Installation tools for self tapping thread inserts - see the linked inserts categories
Related Information:
Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon - Self Tapping.
Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.
Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer. This category may be available in the new MBA online store at
Inserts - Thread Repair - Keylocking Starter Sets.
Related Information:
Tri-Lobe Course Thread Plastic Threading Screws
Tri-Lobe Course Thread Plastic Threading Screws
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Type AB Steel Self Tapping Screws.
Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.
Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.
The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout. This category may be available in the new MBA online store at
Inserts - Tapered Fit - Finserts - For Wood and Plastics.
Contains a selection of E-Z Lok inserts
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at
Tools - General.
Individual Inserts for use with the Klik Thread Setter Tool
These blind threaded inserts offer strong torque and pull out characteristics. Especially effective in sheet metal and other thin material. Insert is placed into the hole in the parent material and crimped up with the installation tool. Installs from one side - no tapping required. Installs almost flush eliminating the need for countersinking. Made from plated steel. This category may be available in the new MBA online store at
Inserts - Rivet Nuts - Klik - Ribbed.
Related Information:
316 stainless conveyor bearings with plastic cage and plastic hex insert
316 stainless conveyor bearings with plastic cage and plastic hex insert
Nylon Insert for Locking. Not NylocTM brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon Insert - Aluminium.
Related Information:
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon Insert - Stainless Steel.
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Nylon Insert - Steel.
Insert bits for use with hand type screwdriver bit holders
This category may be available in the new MBA online store at
Bits - Insert.
Spacers for printed circuit boards
These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw. This category may be available in the new MBA online store at
Spacers - PCB.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Individual Inserts for use with the Klik Thread Setter Tool
These threaded inserts can be used in blind or through hole applications. Featuring a heavy duty thread profile and increased thickness in the collapse area. Steel with cadmium plating. This category may be available in the new MBA online store at
Inserts - Rivet Nuts - Klik - Standard.
Related Information:
Individual Inserts for use with the Klik Thread Setter Tool
These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.
Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.
Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
Related Information:
Also known as keenserts.
Related Information:
Used to insert keylocking inserts - keensert style. Keylocking inserts can be wound in without these tools but the tools make the job much easier. Also known as keenserts.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.