Delays on shipments from USA and shipments passing through Singapore
Shipments from the USA are currently experiencing delays due to severe weather conditions. Shipments passing through Singapore are experiencing some minor delays due to Covid restrictions. We will keep you updated if your orders are affected.
Inserts Self Tapping For Aluminium Stainless 303 Categories
Thread Inserts
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Wood - Hex Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Inserts - Self Tapping - For Plastics - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Couplings - Double Disk - Aluminium
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
Pins - Ball Lock - T-Handle - Industrial - Stainless Steel and Aluminium
Quick release. 17-4 PH or 15-7 MO Stainless Steel pins. Handles are aluminium alloy. Tee handle.
Positive lock detent pins. Aluminium handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Housings - Pillow Block - Washdown
Also see combined categories:
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
All Spyraflo Pillow Block Mounted Bearings
All Spyraflo Mounted Bearings
Spyraflo electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Pins - Ball Lock - L-Handle - Industrial - Stainless Steel
Quick release. 17-4 PH or 15-7 MO Stainless Steel pins. Handles are aluminium alloy.
Positive lock detent pins. Aluminium handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Screws - Self Tapping - Countersunk - Philips - 304 Stainless
Countersunk screws length includes head. ie, the full overall length of the screw.
Screws - Self Tapping - Countersunk - Philips - 316 Stainless
Countersunk screws length includes head. ie, the full overall length of the screw.
Screws - Self Tapping - Pan Head - 316 Stainless
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
Screws - Self Tapping - Pan Head - 302 - 304 Stainless
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
Couplings - Sleeve Type - Hubs
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
Couplings - Sleeve Type - Sleeves
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Inserts - Self Tapping - For Wood - Slotted Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Inserts - Self Tapping - For Wood - Slotted Drive - Short
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.
Inserts - Expansion - Press In - 303 Stainless - Flanged
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Inserts - Expansion - Press In - 303 Stainless Steel
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Tools - Installation - For Self Tapping Inserts
Installation tools for self tapping thread inserts - see the linked inserts categories
Related Information:
Pins - Locating - Spring - Stainless Pin - Unsealed
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Inserts - Thread Repair - Keylocking
Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.
Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
Related Information:
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Inserts - Thread Repair - Keylocking Starter Sets
Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.
Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.
Related Information:
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Couplings - Slit Type - Standard
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
Related Information:
Housings - Bearing - Pillow Block - Miniature
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination.
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.
Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.
Related Information:
Pulleys - Timing - 5.000mm Pitch - GT2 - 15mm Wide - Through Bore
Timing Pulleys to suit GT 5.000mm Pitch Timing Belts. Suits belts 15mm wide. Aluminium, steel and cast iron.
Aluminium Alloy and Black Oxide Coated Steel. Aluminium types have finished bore and grub screws. Steel type have unfinished bores. Unfinished types requires drilling and tapping.
Related Information:
Pins - Ball Lock - Button Handle - Stainless Steel
17-4 PH or PH15-7MO stainless steel spindle and shank. Handles aluminium unless noted otherwise.
Positive lock detent pins. Aluminium handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Couplings - Rigid - Set Screw
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
Related Information:
Pins - Ball Lock - Ring Handle - Industrial - Stainless Steel
17-4 PH or PH15-7MO stainless steel spindle and shank. Handles aluminium unless noted otherwise.
Positive lock detent pins. Aluminium handles. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 12.7mm Wide - Through Bore
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Through Bore
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Pulleys - Timing - 9.525mm Pitch - L - 25.4mm Wide - Through Bore
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.
Related Information:
Linear Slides - Utilitrak - CR - Channels
Use with Utilitrak CR Carriages. Composite heat treated stainless steel mounted to an extruded aluminium base. Match by size.
Related Information:
Nuts - Hexagonal - Nylon Insert - Aluminium
Nylon Insert for Locking. Not NylocTM brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
Related Information:
Washers - Self Aligning - Sets - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Components - Stainless Steel
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Housings - Igubal - Sliding
Housing: Aluminium. Insert: Sliding film Iglidur(R) J. Tolerance for the Shaft: h7. Use with Drylin aluminium shafts.
Related Information:
Housings - Bearing - Flanged - 2 Bolt Hole - Aluminium
Starting at 8mm bore size, aluminium silver series housings with removable chrome steel bearing
Couplings - Spider Type C - Complete
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.
Related Information:
Locknuts - Stainless Insert
Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (P’) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.
Related Information:
Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Bearings - Acetal with Stainless Balls - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Pins - Ball Lock - Button Handle - Commercial
Quick release. Stainless steel commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed.
Economical. Positive lock detent pins. Aluminium handles. 360 Brass Buttons. Commercial Carbon Steel Shank and balls. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Snaps - Swivel Eye - Aluminium
Rust proof nickel plated made from finest quality zinc aluminium alloy
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127000 products in 2359 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
