Inserts Expansion Press In 303 Stainless Flanged Categories
Thread Inserts
Inserts - Expansion - Press In - 303 Stainless - Flanged
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Inserts - Expansion - Press In - 303 Stainless Steel
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
Inserts - Expansion - Press In - Brass - Flanged
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Inserts - Expansion - Press In - Brass - Standard
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Inserts - Thread Repair - Keylocking
Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.
Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
Related Information:
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Mounts - Vibration Isolation - Compression - Stainless Steel
Compression shear mounts for harsh environments.
Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.
Related Information:
Locknuts - Stainless Insert
Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (P’) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.
Related Information:
Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nylon Insert for Locking. NylocTM and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at Nuts - Hexagonal - Nylon Insert - Stainless Steel.
Inserts - Self Tapping - For Aluminium - Stainless 316
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Easy to install with a standard tap, bolt and wrench.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Bearings - Conveyor - Hex Bore - Double Row - Stainless Steel
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Double Row - Stainless Steel.
Bearings - Conveyor - Hex Bore - Single Row - Stainless Steel
316 stainless conveyor bearings with plastic cage and plastic hex insert
Loads and Speeds are for reference only. Testing recommended. This category may be available in the new MBA online store at Bearings - Conveyor - Hex Bore - Single Row - Stainless Steel.
Gears - Spur - 24DP - 20 Degree - Plastic with Insert
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic with Insert.
Bearings - Spherical OD For Plastic Housings - 316 Stainless Steel
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Bearings - Spherical OD For Plastic Housings - Acetal - with Stainless Balls
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Gears - Spur - 24DP - 20 Degree - Plastic - Plain
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic - Plain.
Housings - Tapped Base Unit - Stainless
Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.
Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.
Gears - Spur - Module 1.25 - Stainless
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.
Gears - Spur - Module 0.5 - Stainless
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.
Gears - Spur - Module 0.8 - Stainless
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.
Inserts - Thread Repair Sets Recoil
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Gears - Spur - 24DP - 20 Degree - Stainless
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Stainless.
Gears - Spur - 48DP - 20 Degree - Stainless
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Stainless.
Keys - Woodruff - 303 Stainless Steel
This category may be available in the new MBA online store at Keys - Woodruff - 303 Stainless Steel.
Related Information:
Screws - Captive - Thumb - 303 Stainless
Knurled Head. This category may be available in the new MBA online store at Screws - Captive - Thumb - 303 Stainless.
Related Information:
Shafting - Ground - Precision - Stainless 303 Grade
Precision ground shafting.
This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.
Related Information:
Plungers - Ball Threaded - 303 Stainless Steel - Nylon Balls
Items shown with Long-Lok have a dry threadlocking sealant applied to thread. This category may be available in the new MBA online store at Plungers - Ball Threaded - 303 Stainless Steel - Nylon Balls.
Screws - Shoulder - Socket Head - 303 Stainless
Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - 303 Stainless.
Screws - Shoulder - Philips Head - Stainless
303 Stainless Steel
Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Philips Head - Stainless.
Screws - Shoulder - Slotted Head - Stainless
303 Stainless Steel
Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Slotted Head - Stainless.
Screws - Panel - Stainless
Extra large head. One piece construction. 303 Stainless Steel.
This category may be available in the new MBA online store at Screws - Panel - Stainless.
Mounts - Levelling Studded - 303 Stainless - Standard
Levelling adjusters. Good quality with value pricing. 303 stainless steel.
Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces. This category may be available in the new MBA online store at Mounts - Levelling Studded - 303 Stainless - Standard.
Plungers - Indexing - Pull Knob - 303 Stainless - With Nut
With thermoplastic knob
This category may be available in the new MBA online store at Plungers - Indexing - Pull Knob - 303 Stainless - With Nut.
Plungers - Spring - Threaded - Stainless and Acetal
303 Stainless Steel body and acetal nose
Items shown with Long-Lok have a dry threadlocking sealant applied to thread. This category may be available in the new MBA online store at Plungers - Spring - Threaded - Stainless and Acetal.
Plungers - Spring - Threaded - Stainless and Plastic
303 Stainless Steel body with plastic nose
Items shown with Long-Lok have a dry threadlocking sealant applied to thread. This category may be available in the new MBA online store at Plungers - Spring - Threaded - Stainless and Plastic.
Plungers - Ball Threaded - 303 Stainless Steel with Threadlock
With Long-Lok thread locking compound to prevent loosening
Items shown with Long-Lok have a dry threadlocking sealant applied to thread. This category may be available in the new MBA online store at Plungers - Ball Threaded - 303 Stainless Steel with Threadlock.
Screws - Thumb - Shoulder
303 Stainless Steel
This category may be available in the new MBA online store at Screws - Thumb - Shoulder.
Related Information:
Mounts - Anti-Vibration - 303 Stainless Steel
Corrosion resistant designed with high grade nitrile rubber and stainless steel.
Swivel movement plus or minus 7o for stable support on inclined floors. Nitrile rubber base helps ensure stability. This category may be available in the new MBA online store at Mounts - Anti-Vibration - 303 Stainless Steel.
Related Information:
Collars - Hex Bore - One Piece - 303 Stainless Steel
This category may be available in the new MBA online store at Collars - Hex Bore - One Piece - 303 Stainless Steel.
Related Information:
Collars - Hex Bore - Two Piece - 303 Stainless Steel
This category may be available in the new MBA online store at Collars - Hex Bore - Two Piece - 303 Stainless Steel.
Related Information:
Plungers - Indexing - Locking - With Knob - 303 stainless Steel
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
303 Stainless Steel. This category may be available in the new MBA online store at Plungers - Indexing - Locking - With Knob - 303 stainless Steel.
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Stainless Steel.
Related Information:
Washers - Heavy Duty - Machined - Stainless Steel
303 Stainless Steel
This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Stainless Steel.
Related Information:
Knobs - Ball Threaded Female - Stainless Steel
303 stainless steel (European grade 1.4305)
This category may be available in the new MBA online store at Knobs - Ball Threaded Female - Stainless Steel.
Related Information:
Plungers - Indexing - Pull Knob - Full 303 Stainless - With Nut
With thermoplastic knob
This category may be available in the new MBA online store at Plungers - Indexing - Pull Knob - Full 303 Stainless - With Nut.
Threaded Rod - Allthread - Stainless Steel - 304
UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.
This category may be available in the new MBA online store at Threaded Rod - Allthread - Stainless Steel - 304.
Spacers - Round - Threaded
Brass or 303 Stainless Steel
This category may be available in the new MBA online store at Spacers - Round - Threaded.
Plungers - Indexing - Non Locking - With Knob - 303 Stainless Steel
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
303 Stainless Steel.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
