Small Parts & Bearings - an MBA company

Covid-19 Update!! Current supply status.

Trading by online order and email.
Outbound Deliveries: Allow a few extra days for both Australian and overseas deliveries.
Pre-orders and Backorders: Allow a few extra days due to quarantine precautions.

HUBS CATEGORIES


Hubs - Gear and Dial - Single
Hubs - Gear and Dial - Single

Also see combined categories:
All Hubs

Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

Related Information:


Ratchets - With Hub
Ratchets - With Hub


Match with pawls listed on this site.


Related Information:


Ratchets - Without Hub
Ratchets - Without Hub


Match with pawls listed on this site.


Related Information:


Couplings - Oldham - Hubs - Clamp Style
Couplings - Oldham - Hubs - Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Hubs

0.06 to 44 Nm. Max Speed: 3000 RPM.

Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only


Match with sleeves from sleeves category


Related Information:


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Size List Popular Bicycle Hub Parts
Size List Popular Bicycle Hub Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Rollers - Urethane Feed - With Hub
Rollers - Urethane Feed - With Hub

Also see combined categories:
All Tyred OD Bearings
All Rollers

Urethane coated aluminium alloy feed rollers with hub.

Roller - Urethane 60 Durometer, Ground Outside Diameter. Sleeve - Aluminium.

Related Information:


Couplings - Spider Type B - Hubs Only
Couplings - Spider Type B - Hubs Only


Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.

Related Information:


Couplings - Spline Type - Spare Hubs
Couplings - Spline Type - Spare Hubs

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:


Couplings - Three Jaw Type - Hubs
Couplings - Three Jaw Type - Hubs


Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.

Complete with keyway and set screw. No lubrication needed.

Related Information:


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Check Size Before Ordering DT Swiss Hubs Parts
Check Size Before Ordering DT Swiss Hubs Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only


Match with hubs from hubs category


Related Information:


Pulleys - Timing - 5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub
Pulleys - Timing -  5.000mm Pitch - HTD - 9mm Wide - Plastic - Fairloc Hub

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Fairloc locking hub.


Related Information:


Pulleys - Timing - 2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub
Pulleys - Timing -  2.032mm Pitch - MXL - 6.4mm Wide - Plastic - Metal Hub

Also see combined categories:
All MXL 2.032mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.

2.032mm metric is equivalent to 0.080 pitch imperial.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Plastic - Metal Hub
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Plastic - Metal Hub

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Metal Hub.


Related Information:


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Couplings - Double Disk - Aluminium
Couplings - Double Disk - Aluminium


Zero Backlash - High Torsional Stiffness.

Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.

Related Information:


Couplings - Three Jaw Type - Inserts
Couplings - Three Jaw Type - Inserts


Match with Three Jaw Type hubs by OD

Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.

Related Information:


Cranks - Handwheel - Spoked
Cranks - Handwheel - Spoked

Also see combined categories:
All Spoked Handwheel Cranks

Pressed steel with RAL 9005 black epoxy resin coating. Hub: Welded with H9 tolerance plain hole (Type B) or through square H11 tolerance hole (Type V). Axial and radial runout lower than IT 12.


Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Couplings - Spider Type B - Complete
Couplings - Spider Type B - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.

Related Information:


Assemblies - Locking - Flanged
Assemblies - Locking - Flanged

Also see combined categories:
All Locking Assemblies

Suitable for locking sprockets, pulleys, eccentric shafts.

Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.


Couplings - Spider Type C - Complete
Couplings - Spider Type C - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.

Related Information:


Couplings - K Type
Couplings - K Type


Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Couplings - Bellows - Set Screw - 316 Stainless
Couplings - Bellows - Set Screw - 316 Stainless

Also see combined categories:
All Bellows Couplings

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Collars - Shaft - Hinged - Stainless Steel
Collars - Shaft - Hinged - Stainless Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Collars - Shaft - Hinged - Steel
Collars - Shaft - Hinged - Steel

Also see combined categories:
All Round Bore Shaft Collars
All Hinged Shaft Collars

Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)

Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.

Related Information:


Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - EZ-Lock
Pulleys - Timing -  2.000mm Pitch - GT2 - 6mm Wide - EZ-Lock

Also see combined categories:
All 2mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.

Aluminium Alloy. EZI-LOK Hub Clamps together wit a Socket Head Cap Screw. Socket Cap Screw is Supplied with Pulley.

Related Information:


Pulleys - Timing - 3.000mm Pitch - GT2 - 9mm Wide - EZ-Lock
Pulleys - Timing -  3.000mm Pitch - GT2 -  9mm Wide - EZ-Lock

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide.

Aluminium Alloy. EZ-Lock hub clamps to the shaft with a socket head cap screw. Cap screw is supplied with the pulley.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Sprockets - 9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x4.7mm steel chain (35-1 ASA)

Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch.

Related Information:


Pulleys - Timing - 2.000mm Pitch - GT2 - 6mm Wide - Through Bore
Pulleys - Timing -  2.000mm Pitch - GT2 - 6mm Wide - Through Bore

Also see combined categories:
All 2mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.

Aluminium Alloy. Set Screw and EZI-LOK Hubs.

Related Information:


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.


Pulleys - Timing - 3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless
Pulleys - Timing -  3.000mm Pitch - HTD - 9mm Wide - Plastic - Hubless

Also see combined categories:
All 3mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.

Suitable for use with shaftloc sleeves.

Related Information:


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Reducers - Bore
Reducers - Bore


Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.

S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.

Related Information:


Pulleys - Timing - 5.000mm Pitch - T5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - T5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts. Suits belts 9.5 to 10.0mm wide.

Aluminium alloy. No locking provided. You will need to drill and tap the hub to suit your desired grub screw. Tapped hubs can be provided on request.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126893 products in 2409 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126893 products in 2409 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.