Bearings Mounted
Low profile self aligning flange mounted high temperature PTFE bronze bearings
Related Information:
Low profile self aligning flange mounted low temperature PTFE bronze bearings
Related Information:
Low profile self aligning flange mounted PTFE bronze bearings
Related Information:
Low profile self aligning flange mounted sintered bronze bearings
Related Information:
Low profile flange mounted PTFE bronze bearings
Related Information:
Spyraflo robust light weight aluminium housing with self aligning bronze bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Low profile self aligning flange mounted acetal Delrin bearings
Related Information:
Low profile self aligning flange mounted acetal Delrin AF bearings
Related Information:
Low profile self aligning flange mounted needle roller bearings
Related Information:
You may also be interested in
Linear Bearings with Housing
Single and double length
Bearings Mounted
Spyraflo robust light weight aluminium housing with porous sintered bronze
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Spyraflo low profile self aligning flange mounted acetal Delrin bearings
Related Information:
Spyraflo low profile self aligning flange mounted acetal Delrin AF bearings
Related Information:
Spyraflo sintered bronze bearing in a special self-clinching steel housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
Spyraflo robust light weight aluminium housing with self aligning needle roller bearings
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Low profile flange mounted needle roller bearings
Related Information:
Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs. Simplify designs.
Small and cost effective. All bore sizes are mounted in the same size housing for ease of design and cost efficiency. High precision bearings pre-mounted with a 5o misalignment capability. 40,000 RPM recommended maximum speed with testing. 27kgf radial static capacity, 54kgf radial dynamic capacity per bearing. RoHS, REACH and SVHC environmental compliant.
Spyraflo robust light weight aluminium housing with self aligning needle roller bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Spyraflo acetal bearings in a special steel self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
Spyraflo electroless nickel plated aluminium housing with stainless steel coated self aligning acetal bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Electroless nickel plated aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs and simplify designs. Designed to press into a mounting plate as thin as 1.5mm.
Clinches into a plate bored to the required housing bore. Minimum plate thickness 1.6mm to no maximum. Maximum mounting hardness 100 Rockwell B. Operating temperature Minus 34 oC to Plus 121 Deg C. Compensates for mounting hole tolerances up to 0.07mm. 4.76 to 10mm bores. RoHS, REACH and SVHC environmental compliant.
With integral self aligning plain bearing.
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage. Up to 1000 deg C without a cage or seals.
Related Information:
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC.
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Plastic spherical plain bearings. Also known as ball bushings.
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsuis. Maximum Load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Rubber base is vulcanised to the housing and contains no voids for a completely hygienic seal. Full range of motion up to 10 degrees. Pivot provides secure footing and vibration control. Meets USDA requirements for food processing equipment. This category may be available in the new MBA online store at
Mounts - Leveling - Studded - Hygienic - 304 Stainless.
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3
o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at
Washers - Self Aligning - Components - Stainless Steel.
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3
o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at
Washers - Self Aligning - Sets - Hardened Steel.
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3
o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at
Washers - Self Aligning - Sets - Stainless Steel.
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Related Information:
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination. This category may be available in the new MBA online store at
Housings - Bearing - Pillow Block - Miniature.
Related Information:
20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.
Switchs are rated at 10amp @ 600VAC with finger safe screw terminals. This category may be available in the new MBA online store at
Switches - Rocker.
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Levelling adjusters. Protects general metalworking processes equipment including punch presses, milling machines, lathes, mixers, injection moulding machines, grinders from shock and vibration.
Simplifies installation. 63.5mm of neoprene provides controlled deflections under load. High isolation efficiency for vibration and shock forces, and reduction of transmitted sound. Adjustable up to 12.7mm above loaded height by a few turns of the leveling bolt and tightening the checknut. Corrosion resistant outer housing provides high strength. Neoprene elastomer resists oil, grease, ozone and caustics. Zinc plated hardware resists rust. Hex head bolt and locknut finished with mounts. Height dimensions indicate free height of mount under no load. OSHA Yellow Steel Cover over elastomer base.
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.