Small Parts & Bearings - an MBA company

GRA32 SKF


Cross Referenced Part Numbers



RRA-310 SKF part number GRA3.2

Matches our part number


Description: Brand: Anderton / Seeger / Huyett. Suits E-Clip OD: 6.80. Suits E-Clip: ECL-0032-0045-S42.

Group: Tools - E-Clip Applicators
Part Link: RRA-310

Rec. Retail Price: 0.00. Stock: 1  




RRA-310 SKF part number GRA3.2

Matches our part number


Description: Brand: Anderton / Seeger / Huyett. Suits E-Clip OD: 6.80. Suits E-Clip: ECL-0032-0045-S42.

Group: Tools - E-Clip Applicators
Part Link: RRA-310

Rec. Retail Price: 0.00. Stock: 1  



Category Matches

Latches Draw


Latches - Draw - Over Centre - 300 Grade Stainless Steel
Latches - Draw - Over Centre - 300 Grade Stainless Steel

Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.

Keepers included. Type SC-97533 has a hole for a padlock.



Gears Inch Bevel


Gears - Bevel - 32 Diametrical Pitch - Brass
Gears - Bevel - 32 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
32 DP Mitre Gears


Gears - Bevel - 32 Diametrical Pitch - Plastic
Gears - Bevel - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
32 DP Mitre Gears


Gears Inch Internal


Gears - Internal - 32 Diametrical Pitch - Aluminium
Gears - Internal - 32 Diametrical Pitch - Aluminium

Also see combined categories:
All Imperial Internal Gears
All Internal Gears

2024-T4 Aluminum





Gears - Internal - 32 Diametrical Pitch - Stainless
Gears - Internal - 32 Diametrical Pitch - Stainless

Also see combined categories:
All Imperial Internal Gears
All Internal Gears

303 stainless steel.



Gears Inch Mitre


Gears - Mitre - 32 Diametrical Pitch - Brass
Gears - Mitre - 32 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


Gears - Mitre - 32 Diametrical Pitch - Plastic
Gears - Mitre - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


Gears - Mitre - 32 Diametrical Pitch - Steel
Gears - Mitre - 32 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


Pinion Wire Imperial


Gears - Pinion Wire - 32 Diametrical Pitch
Gears - Pinion Wire - 32 Diametrical Pitch

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.



Gearboxes Offset


Gearboxes - Offset - 80 x 64 x 32
Gearboxes - Offset -  80 x  64 x  32

Also see combined categories:
All Offset Gearboxes

FF15 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Gear: High Carbon Steel 817M40(EN24). Weight: 0.55kg. Backlash: 1o. Hours Life: 12000 hr. Max Input Speed: 2000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. You will need to assess duty, cycles and confirm gearbox suitability with your own calculations. Torque figures are to be used for guidance only.

Related Information:
Inexpensive Gearmotor Kits
Output Shafts


You may also be interested in

Gears Inch Spur


Gears - Spur - 32DP - 14.5 Degree - Brass
Gears - Spur -  32DP - 14.5 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 14.5 Degree - Plastic
Gears - Spur -  32DP - 14.5 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 14.5 Degree - Steel
Gears - Spur -  32DP - 14.5 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Aluminium
Gears - Spur -  32DP - 20 Degree - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Brass
Gears - Spur -  32DP - 20 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Plastic
Gears - Spur -  32DP - 20 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Stainless
Gears - Spur -  32DP - 20 Degree - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Steel
Gears - Spur -  32DP - 20 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. Carbon Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Plastic with Insert
Gears - Spur -  32DP - 20 Degree - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Universal Joint Covers


Covers - Universal Joint - Elasticate Rubber
Covers - Universal Joint - Elasticate Rubber

Also see combined categories:
All Universal Joint Covers

For Single and Double Universal Joints.

-27 oC to 70 Deg C temp range (constant). -32 oC to 120 Deg C temp range (intermittent).

Related Information:
Universal Joints


Thread Inserts


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.



Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.



Gears Inch Racks


Gear Racks - 32DP - 14.5 PA - Brass
Gear Racks -  32DP - 14.5 PA - Brass

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gear Racks - 32DP - 14.5 PA - Plastic
Gear Racks -  32DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Spur


Gears - Spur - 32DP - Stem - Stainless
Gears - Spur -  32DP - Stem - Stainless

Also see combined categories:
All Imperial Spur Gears
All Imperial Stem Gears

303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Racks


Gear Racks - 32DP - 14.5 PA - Steel
Gear Racks -  32DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Carbon Steel. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gear Racks - 32DP - Stainless Steel
Gear Racks -  32DP - Stainless Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gear Racks - 32DP - Aluminium - Side Holes
Gear Racks -  32DP - Aluminium - Side Holes

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 2024-T4 Aluminium. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gear Racks - 32DP - Stainless - Side Holes
Gear Racks -  32DP - Stainless - Side Holes

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gear Racks - 32DP - Stainless - Tapped Base
Gear Racks -  32DP - Stainless - Tapped Base

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Spur


Gears - Spur - 32DP - Hub Mounting - Aluminium
Gears - Spur -  32DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - Hub Mounting - Stainless
Gears - Spur -  32DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - Hub Mounting - Plastic with Aluminium Core
Gears - Spur -  32DP - Hub Mounting - Plastic with Aluminium Core

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal with aluminium core. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124325 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124325 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.