Small Parts & Bearings - an MBA company

GIP90 REID


Cross Referenced Part Numbers



PLIT-060-127C-56-LK-S3 Reid part number GIP-90





Thread (B): 1/2-13 UNC (12.700mm). Thread Length (E): 20.1. Initial End Force: 0.6.

Retail Price: 0.00 (Each )     
Lower price for quantities     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Gearboxes Cross Axis


Gearboxes - Cross Axis - 90 x 75 x 32mm
Gearboxes - Cross Axis -  90 x  75 x  32mm

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Related Information:


Backup Rings


Rings - Backup
Rings - Backup


Durometer 90 Nitrile Rubber back up rings.

This category may be available in the new MBA online store at Rings - Backup.


Latches Handle


Handles - Latching - T-Handle - Locking
Handles - Latching - T-Handle - Locking

Also see combined categories:
All T Handles

90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.

This category may be available in the new MBA online store at Handles - Latching - T-Handle - Locking.

Related Information:


Ball Screws Rolled


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C. This category may be available in the new MBA online store at Ballscrew - Thomson Saginaw.


Gears Metric Bevel


Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1.5 - Plastic.

Related Information:


Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1 - Plastic.

Related Information:


Gears Inch Bevel


Gears - Bevel - 32 Diametrical Pitch - Plastic
Gears - Bevel - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - 32 Diametrical Pitch - Plastic.

Related Information:


Cross Blocks


Cross Blocks - Heavy Duty - One Knob One Nut
Cross Blocks - Heavy Duty - One Knob One Nut

Also see combined categories:
All Cross Blocks
All Swivel Joints and Cross Blocks

Used for connecting two round rods at 90o.

Adjustments can be made by loosening the hand knob. Plastic knobs function independently for precise adjustment. Knobs have brass insert for easy turning and to prevent galling. Stainlesss steel eye bolt firmly clamps around adjusting rod for superior holding strength. Eyelet does not mar rod when tightened, resulting in smooth rod surface that easily slides through the cross block. No set screws required. Plastic or Stainless bodies accept 12.70 or 15.88mm rods. This category may be available in the new MBA online store at Cross Blocks - Heavy Duty - One Knob One Nut.


You may also be interested in

Bushes Plastic


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


O-Rings


O-Rings - Cord
O-Rings - Cord


Nitrile, Fluoroelastomer and EPDM continuous length o-ring cord.

Nitrile: Temp Range: -30oC to +90oC / Fluoroelastomer: Temp Range -20oC to +240oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Nitrile: Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Fluoroelastomer (Viton(R)): Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis. This category may be available in the new MBA online store at O-Rings - Cord.

Related Information:


Mounts Machinery


Mounts - Neoprene Pads - Ribbed Pattern
Mounts - Neoprene Pads - Ribbed Pattern

Also see combined categories:
All Mounting Pads

Provides a versatile, inexpensive way to isolate shock, vibration and reduce noise levels.

Simply lift the machine and slide the pads under each foot. Provides firm footing to floor and equipment. Ribbed pads can be stacked with the ribs at 90o to each other or nested with the ribs in the grooves. Scored in 50.8mm squares for easy cutting. Oil resistant neoprene rubber.

Related Information:


O-Rings


O-Rings - Nitrile Rubber
O-Rings - Nitrile Rubber

Also see combined categories:
All O-Rings

General purpose. Includes o-rings for dental handpiece applications.

Temperature Range: -30oC to +90oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. This category may be available in the new MBA online store at O-Rings - Nitrile Rubber.

Related Information:


O-Rings - Quad
O-Rings - Quad

Also see combined categories:
All O-Rings

Quadrings or quattrorings reduce the amount of squeeze needed for positive seal, reducing friction and extending seal life.

Temperature Range: -30oC to +90oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Also known as quad rings. This category may be available in the new MBA online store at O-Rings - Quad.

Related Information:


Gearheads Inline


Gearheads - Inline - Planetary - Size 17 - Precision
Gearheads - Inline - Planetary - Size  17 - Precision

Also see combined categories:
All Inline Planetary Gearheads

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Related Information:


Shafting General Purpose


Rod - Drill - O-1 Oil Hardening
Rod - Drill - O-1 Oil Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - O-1 Oil Hardening.


Linear Slides


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds. This category may be available in the new MBA online store at Slides - Linear - Cross Roller Rail.


Gears Metric Mitre


Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1.5 - Brass.

Related Information:


Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Brass.

Related Information:


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:


Gears - Mitre - 24 Diametrical Pitch - Brass
Gears - Mitre - 24 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 24 Diametrical Pitch - Brass.

Related Information:


Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Zinc Diecast.

Related Information:


Gears - Mitre - 24 Diametrical Pitch - Plastic
Gears - Mitre - 24 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 24 Diametrical Pitch - Plastic.

Related Information:


Gears - Mitre - 10 Diametrical Pitch - Steel
Gears - Mitre - 10 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 10 Diametrical Pitch - Steel.


Gears - Mitre - 12 Diametrical Pitch - Steel
Gears - Mitre - 12 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 12 Diametrical Pitch - Steel.


Gears - Mitre - 16 Diametrical Pitch - Steel
Gears - Mitre - 16 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Unhardened Steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 16 Diametrical Pitch - Steel.


Gears - Mitre - 8 Diametrical Pitch - Steel
Gears - Mitre -  8 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 8 Diametrical Pitch - Steel.


Oil Seals - Nitrile Rubber
Oil Seals - Nitrile Rubber

Also see combined categories:
All Oil Seals

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifically required please let us know when ordering.

Operating Temp. Range: -30oC to +90oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. This category may be available in the new MBA online store at Oil Seals - Nitrile Rubber.


9000 Abu Garcia Parts
9000 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


9000C Abu Garcia Parts
9000C Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


9072702 Long Arm Jentschman Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 1.5 - Steel.

Related Information:


Gears - Mitre - Spiral - Module 3.5 - Steel
Gears - Mitre - Spiral - Module 3.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 3.5 - Steel.


1900B Planer Makita Parts
1900B Planer Makita Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Circlips - Internal - Bevelled
Circlips - Internal - Bevelled

Also see combined categories:
All Internal Circlips

N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments. This category may be available in the new MBA online store at Circlips - Internal - Bevelled.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - Clean - 3.2mm Wide
Belts - Timing -  2.032mm Pitch - MXL - Clean - 3.2mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

PowerGrip(R) TruMotion(R) Timing Belts in 2.032mm or 0.080 inch pitch.

The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oC to +90oC, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. TruMotion(R) belts have a durable wear surface for longer life and are RoHS compliant. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. RoHs compliant.

Related Information:


Circlips - External - Grooveless
Circlips - External - Grooveless

Also see combined categories:
All External Circlips

Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).

Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. This category may be available in the new MBA online store at Circlips - External - Grooveless.

Related Information:


Motors - DC 24.3X12.35 mm
Motors - DC 24.3X12.35 mm

Also see combined categories:
All DC Motors

6.0 VDC - 4,900 RPM unloaded at 4.5 volts

This category may be available in the new MBA online store at Motors - DC 24.3X12.35 mm.

Related Information:


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Wire - Steel - Spring - Music - Coils
Wire - Steel - Spring - Music - Coils

Also see combined categories:
All Spring Wire

SAE 1090 Spring Steel.

This category may be available in the new MBA online store at Wire - Steel - Spring - Music - Coils.

Related Information:


Wire - Steel - Spring - Music Wire - Short Lengths
Wire - Steel - Spring - Music Wire - Short Lengths

Also see combined categories:
All Spring Wire

SAE 1090 Spring Steel. Includes inch and metric sizes.

Metric and imperial. Shipped in sturdy mail tubes. This category may be available in the new MBA online store at Wire - Steel - Spring - Music Wire - Short Lengths.

Related Information:


Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch. This category may be available in the new MBA online store at Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Tools - Taps - Carbon Steel - Hand
Tools - Taps - Carbon Steel - Hand

Also see combined categories:
All Taps
All Tools

Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

Carbon steel hand taps. Carbon Steel (CS) Hand taps. This category may be available in the new MBA online store at Tools - Taps - Carbon Steel - Hand.


Tools - Taps - High Speed Steel - Hand
Tools - Taps - High Speed Steel - Hand

Also see combined categories:
All Taps
All Tools

High Speed Steel Short Machine Flute Taps. starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

High Speed Steel (HSS) Short Machine taps. This category may be available in the new MBA online store at Tools - Taps - High Speed Steel - Hand.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 141362 products in 2026 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 141362 products in 2026 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.