Small Parts & Bearings - an MBA company

GHP55 REID


Cross Referenced Part Numbers



BLP-079-0381-THD-S17 Reid part number GHP-55A





Nominal Diameter: 7.94. Grip Length: 38.10. Pin Material Grade: 17-4 PH Stainless Stainless.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     



BLP-079-0381-THD-S17 Reid part number GHP-55





Nominal Diameter: 7.94. Grip Length: 38.10. Pin Material Grade: 17-4 PH Stainless Stainless.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Studs


Studs - Ball - Threaded
Studs - Ball - Threaded


Zinc Plated Steel DIN 71803 Form C. Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened).


O-Rings


O-Rings - EPDM Rubber
O-Rings - EPDM Rubber

Also see combined categories:
All O-Rings

Suitable for heated water and steam.

Temperature Range: -55oC to +150oC. Chemically resistant to Hydraulic Fluids. Resistant to alcohols, glycol engine coolants and SKY-DROL (phosphate ester hydraulic fluid).

Related Information:


You may also be interested in

Gearheads Inline


Gearheads - Inline - Planetary - Size 17 - Precision
Gearheads - Inline - Planetary - Size  17 - Precision

Also see combined categories:
All Inline Planetary Gearheads

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Related Information:


557 Push Button Lares Parts
557 Push Button Lares Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


557SR Lares Parts
557SR Lares Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


2304LD - 553 5121 Kavo Parts
2304LD - 553 5121 Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Intra 24CN - 24LN - 553 5761 Kavo Parts
Intra 24CN - 24LN - 553 5761 Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Belts - Timing - 14.000mm Pitch - GT - 55mm Wide
Belts - Timing - 14.000mm Pitch - GT -  55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 55mm Wide
Belts - Timing - 14.000mm Pitch - HTD -  55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 55mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT -  55mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 55mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.

Related Information:


3554 Surgical Handpiece Kavo Parts
3554 Surgical Handpiece Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Balls - Stainless Steel - 400 Grade
Balls - Stainless Steel - 400 Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60. Includes 420 and 440C grades

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.

Related Information:


Balls - Checking - Stainless Steel
Balls - Checking - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Fixture - Stainless Steel
Balls - Fixture - Stainless Steel

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Checking - Stainless Steel - With Tapped Shank
Balls - Checking - Stainless Steel - With Tapped Shank

Also see combined categories:
All Fixture and Checking Balls

440C Hardened to RC 55-58.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.


Feeler Gauge Stock - Stainless
Feeler Gauge Stock - Stainless


Used for close spacing and extremely tight tolerance situation.

Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.


Balls - Tooling - One Piece - Construction - Stainless Steel
Balls - Tooling - One Piece - Construction - Stainless Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 440C Stainless Steel heat treated to 55-58 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm.

Related Information:


Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.

440C Stainless Steel heat treated to 55-58 RC.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127135 products in 2361 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127135 products in 2361 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.