Small Parts & Bearings - an MBA company

GERM14 IGUS


Cross Referenced Part Numbers



CLJ-14.00-M14R Igus part number GERM-14





Hole Dia. (d1): 14.0. Depth from Centre (g): 28.0. Top Width (a1 x a2): 27.0 x 27.0.

Online Price: 0.00     
Stock: Pre-Order (due 12 weeks)     
Due dates are estimates only     


Category Matches

Housings with Bearing


Housings - Bearing - Pillow Block - Thermoplastic - W300
Housings - Bearing - Pillow Block - Thermoplastic - W300

Also see combined categories:
All Housings with Integral Bearing

Iglide L280 / Igus W300 Ball with Thermoplatic Body.

Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 oC to +130 oC. Max. Static Tensile Strength is Long Term. Info for Short Term also available.


Housings - Igubal - Sliding
Housings - Igubal - Sliding

Also see combined categories:
All Housings with Integral Bearing

Housing: Aluminium. Insert: Sliding film Iglidur(R) J. Tolerance for the Shaft: h7. Use with Drylin aluminium shafts.

Related Information:


Shafting - Aluminium
Shafting - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.


Housings - Bearing - Flanged - Square - W300
Housings - Bearing - Flanged - Square - W300

Also see combined categories:
All Housings with Integral Bearing

With integral self aligning plain bearing.

Housing : Igumid G. Ball : Highly wear resistant Iglidur W300. Temperature range -40 oC to +180 oC.


Housings - Bearing - Flanged - 2 Bolt Hole - W300
Housings - Bearing - Flanged - 2 Bolt Hole - W300

Also see combined categories:
All Housings with Integral Bearing

With integral self aligning plain bearing.

Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.


Spring Motor Assemblies - Open - RINO
Spring Motor Assemblies - Open - RINO

Also see combined categories:
All Spring Motors

Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.

Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.


Latches - 1-4 Turn - Simple
Latches - 1-4 Turn - Simple


With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.

The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Latches - 1-4 Turn -Tee Handle - Non Locking
Latches - 1-4 Turn -Tee Handle - Non Locking

Also see combined categories:
All Quarter Turn Latches

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Screws - Thumb - 1-4 Turn
Screws - Thumb - 1-4 Turn

Also see combined categories:
All Thumb Screws


Related Information:


Pins - Taper - Imperial - Standard - Carbon Steel
Pins - Taper - Imperial - Standard - Carbon Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.


Related Information:


Pins - Taper - Imperial - Standard - Stainless Steel
Pins - Taper - Imperial - Standard - Stainless Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.


Related Information:


Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel
Pins - Taper - Imperial - Extractable - External Thread - Stainless Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.

Threaded externally for easy extraction.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 115mm Wide
Belts - Timing - 14.000mm Pitch - GT - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 170mm Wide
Belts - Timing - 14.000mm Pitch - GT - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 40mm Wide
Belts - Timing - 14.000mm Pitch - GT -  40mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 55mm Wide
Belts - Timing - 14.000mm Pitch - GT -  55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 85mm Wide
Belts - Timing - 14.000mm Pitch - GT -  85mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Pitch (P) - 14.000mm. GT3 replaces GT2 as GT2 stock is depleted. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 115mm Wide
Belts - Timing - 14.000mm Pitch - HTD - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 170mm Wide
Belts - Timing - 14.000mm Pitch - HTD - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 40mm Wide
Belts - Timing - 14.000mm Pitch - HTD -  40mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 55mm Wide
Belts - Timing - 14.000mm Pitch - HTD -  55mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 85mm Wide
Belts - Timing - 14.000mm Pitch - HTD -  85mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 115mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT - 115mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 115mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 170mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT - 170mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 170mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 40mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT -  40mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 40mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast Iron. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 55mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT -  55mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 55mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 85mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT -  85mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 85mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements.

Related Information:


Gear Racks - 10DP - 14.5 PA - Steel
Gear Racks - 10DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - 20DP - 14.5 PA - Steel
Gear Racks - 20DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 20 DP. Approx 3.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - 48DP - 14.5 PA - Steel
Gear Racks -  48DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - 6DP - 14.5 PA - Steel
Gear Racks -  6DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 6 DP. Approx 13.3mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - 8DP - 14.5 PA - Steel
Gear Racks -  8DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 8 DP. Approx 9.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.


Gears - Spur - 10DP - 14.5 Degree - Steel
Gears - Spur -  10DP - 14.5 Degree - Steel

Also see combined categories:
All 10DP Spur Gears

PCD = No. of Teeth x 2.540mm (1/10 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 10 Diametrical Pitch. Approx 7.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 12DP - 14.5 Degree - Steel
Gears - Spur -  12DP - 14.5 Degree - Steel

Also see combined categories:
All 12DP Spur Gears

PCD = No. of Teeth x 2.117mm (1/12 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 12 Diametrical Pitch. Approx 6.65mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 16DP - 14.5 Degree - Steel
Gears - Spur -  16DP - 14.5 Degree - Steel

Also see combined categories:
All 16DP Spur Gears 14.5 Degree
All Metal 16DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 20DP - 14.5 Degree - Steel
Gears - Spur -  20DP - 14.5 Degree - Steel

Also see combined categories:
All 20DP Spur Gears

PCD = No. of Teeth x 1.270mm (1/20 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 20 Diametrical Pitch. Approx 3.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - 14.5 Degree - Brass
Gears - Spur -  24DP - 14.5 Degree - Brass

Also see combined categories:
All 24DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - 14.5 Degree - Steel
Gears - Spur -  24DP - 14.5 Degree - Steel

Also see combined categories:
All 24DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system. Carbon Steel.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - 14.5 Degree - Brass
Gears - Spur -  32DP - 14.5 Degree - Brass

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - 14.5 Degree - Plastic
Gears - Spur -  32DP - 14.5 Degree - Plastic

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - 14.5 Degree - Steel
Gears - Spur -  32DP - 14.5 Degree - Steel

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - 14.5 Degree - Brass
Gears - Spur -  48DP - 14.5 Degree - Brass

Also see combined categories:
All 48DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - 14.5 Degree - Plastic
Gears - Spur -  48DP - 14.5 Degree - Plastic

Also see combined categories:
All 48DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 6DP - 14.5 Degree - Steel
Gears - Spur -   6DP - 14.5 Degree - Steel

Also see combined categories:
All 6DP Spur Gears

PCD = No. of Teeth x 4.233mm (1/6 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 6 Diametrical Pitch. Approx 13.3mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 8DP - 14.5 Degree - Steel
Gears - Spur -   8DP - 14.5 Degree - Steel

Also see combined categories:
All 8DP Spur Gears

PCD = No. of Teeth x 3.175mm (1/8 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 8 Diametrical Pitch. Approx 9.98mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


614A - 624 - 625C - 625D - 627 - 630 - 640 FG Kavo Parts
614A - 624 - 625C - 625D - 627 - 630 - 640 FG Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gear Racks - 12DP - Steel
Gear Racks -  12DP - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - 16DP - Steel
Gear Racks -  16DP - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Latches - 110 Series - Adjustable Grip
Latches - 110 Series - Adjustable Grip


Ultimate strength 145kg. Working strength 120kg.

Strike needs to be ordered separately.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127141 products in 2362 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127141 products in 2362 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.