Small Parts & Bearings - an MBA company

GELM08 IGUS


Cross Referenced Part Numbers



CLJ-08.00-M8L Igus part number GELM-08





Hole Dia. (d1): 8.0. Depth from Centre (g): 16.0. Top Width (a1 x a2): 16.0 x 16.0.

Online Price: 0.00     
Stock: Pre-Order (due 12 weeks)     
Due dates are estimates only     


Category Matches

Housings with Bearing


Housings - Bearing - Pillow Block - Thermoplastic - W300
Housings - Bearing - Pillow Block - Thermoplastic - W300

Also see combined categories:
All Housings with Integral Bearing

Iglide L280 / Igus W300 Ball with Thermoplatic Body.

Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 oC to +130 oC. Max. Static Tensile Strength is Long Term. Info for Short Term also available.


Housings - Igubal - Sliding
Housings - Igubal - Sliding

Also see combined categories:
All Housings with Integral Bearing

Housing: Aluminium. Insert: Sliding film Iglidur(R) J. Tolerance for the Shaft: h7. Use with Drylin aluminium shafts.

Related Information:


Shafting - Aluminium
Shafting - Aluminium

Also see combined categories:
All Shafting
All Aluminium Shafting

Drylin aluminium shafting is recommended for use with Igubal Drylin bearings or Frelon lined bearings only.

Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: Greater than 40um. Surface Hardness: 450-550 HV. Roughness: Ra Less than 0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.


Housings - Bearing - Flanged - Square - W300
Housings - Bearing - Flanged - Square - W300

Also see combined categories:
All Housings with Integral Bearing

With integral self aligning plain bearing.

Housing : Igumid G. Ball : Highly wear resistant Iglidur W300. Temperature range -40 oC to +180 oC.


Housings - Bearing - Flanged - 2 Bolt Hole - W300
Housings - Bearing - Flanged - 2 Bolt Hole - W300

Also see combined categories:
All Housings with Integral Bearing

With integral self aligning plain bearing.

Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.


Spring Motor Assemblies - Open - RINO
Spring Motor Assemblies - Open - RINO

Also see combined categories:
All Spring Motors

Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.

Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.


Belts - Timing - 5.080mm Pitch - XL - 6.4mm Wide
Belts - Timing -  5.080mm Pitch - XL -  6.4mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide
Belts - Timing -  5.080mm Pitch - XL -  7.9mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL - 9.5mm Wide
Belts - Timing -  5.080mm Pitch - XL -  9.5mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL Double Sided - 12.7mm Wide
Belts - Timing -  5.080mm Pitch - XL Double Sided - 12.7mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL Double Sided - 6.4mm Wide
Belts - Timing -  5.080mm Pitch - XL Double Sided -  6.4mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL Double Sided - 7.9mm Wide
Belts - Timing -  5.080mm Pitch - XL Double Sided -  7.9mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.080mm Pitch - XL Double Sided - 9.5mm Wide
Belts - Timing -  5.080mm Pitch - XL Double Sided -  9.5mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  6.4mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.

Aluminium alloy. Finished bore with set screw locking.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Plastic - Insert
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Plastic - Insert

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Brass insert.


Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.

Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - STOCK - Aluminium
Pulleys - Timing -  5.080mm Pitch - XL - STOCK - Aluminium

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys
All XL 5.08mm Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.


Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - STOCK - Carbon Steel
Pulleys - Timing -  5.080mm Pitch - XL - STOCK - Carbon Steel

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys
All XL 5.08mm Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.


Related Information:


Tools - Nut Drivers
Tools - Nut Drivers

Also see combined categories:
All Tools

Includes socket wrench for 0-80 size screws

Lengths shown are based on standard stock but may vary.


Housings - Bearing - Single Assembly
Housings - Bearing - Single Assembly


Includes bearings.

Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.


Circlips - External - Inverted
Circlips - External - Inverted

Also see combined categories:
All External Circlips

N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).

Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.

Related Information:


Circlips - Internal - Inverted
Circlips - Internal - Inverted

Also see combined categories:
All Internal Circlips

M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).

Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.

Related Information:


Flanges - Timing Pulley - Suit 5.080mm XL Series - Aluminium
Flanges - Timing Pulley - Suit  5.080mm XL Series - Aluminium

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys


Related Information:


Flanges - Timing Pulley - Suit 5.080mm XL Series - Carbon Steel
Flanges - Timing Pulley - Suit  5.080mm XL Series - Carbon Steel

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys


Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Tools - Die Nuts
Tools - Die Nuts

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.



Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Tools - Dies - Carbon Steel
Tools - Dies - Carbon Steel

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.



Latches - 1-4 Turn - Simple
Latches - 1-4 Turn - Simple


With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.

The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Belts - Timing - 2.032mm Pitch - MXL - 19.1mm Wide
Belts - Timing -  2.032mm Pitch - MXL - 19.1mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 19.1mm (3/4 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - 3.2mm Wide
Belts - Timing -  2.032mm Pitch - MXL -  3.2mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 3.18mm (1/8 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - 4.8mm Wide
Belts - Timing -  2.032mm Pitch - MXL -  4.8mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 4.76mm (3/16 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - 6.4mm Wide
Belts - Timing -  2.032mm Pitch - MXL -  6.4mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - 7.9mm Wide
Belts - Timing -  2.032mm Pitch - MXL -  7.9mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 7.93mm (5/16 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.032mm Pitch - MXL - 9.5mm Wide
Belts - Timing -  2.032mm Pitch - MXL -  9.5mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 9.53mm (3/8 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.073mm Pitch - 40DP - 3.2mm Wide
Belts - Timing -  2.073mm Pitch - 40DP - 3.2mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide
Belts - Timing -  2.073mm Pitch - 40DP - 4.8mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide
Belts - Timing -  2.073mm Pitch - 40DP - 6.4mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide
Belts - Timing -  2.073mm Pitch - 40DP - 7.9mm Wide

Also see combined categories:
All 40DP 2.073mm Pitch Timing Belts

Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.

Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.

Related Information:


Balls - Plastic - Acrylic
Balls - Plastic - Acrylic

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Related Information:


Housings - Bearing - Square - Miniature
Housings - Bearing - Square - Miniature


Aluminium housings to suit standard radial ball bearings.

Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.


Belts - Timing - 2.032mm Pitch - MXL Double Sided - 6.4mm Wide
Belts - Timing -  2.032mm Pitch - MXL Double Sided - 6.4mm Wide

Also see combined categories:
All MXL 2.032mm Pitch Timing Belts

Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm

Pitch (P) - 2.032mm (0.08 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127134 products in 2361 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127134 products in 2361 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.