Gears Inch Spur
To suit the precision diffs listed on this site. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 64 DP. Approx 1.25mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 64DP - Stainless.
PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 72DP - Stainless.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Stainless.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Stainless.
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.25 - Stainless.
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 24DP - 20 Degree - Stainless.
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 48DP - 20 Degree - Stainless.
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 24DP - 20 Degree - Plastic - Plain.
PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.
PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 64DP - Aluminium.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 24DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 32DP - Stainless Steel.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 48DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 96 DP. Approx 0.83mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless - Side Holes.
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Also known as Heim Joints
Also known as Heim Joints
Also known as Heim Joints
Dimensions not shown are available on request.
Also known as Heim Joints
Spring loaded pull pins allow you to quickly retract and engage the plunger for locating, fastening and quick change operations.
Two part assembly includes a barrel and a plunger assembly. The plunger assembly screws into the housing. The housing is designed to be welded into place for strength. Pulling on the handle of the plunger assembly retracts the plunger into the housing. Releasing the handle allows the spring loaded plunger to extend. 3/8-16 Threaded end so you can add your own handle or knob. 303 stainless steel plunger assembly and housing. Pull up force approx 2.2kg.
Related Information:
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6885
Related Information:
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Related Information:
Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338
Related Information:
One end threaded so you can attach your own handle or knob. 303 Stainless Steel.
Related Information:
An economical way to secure the ends of extension springs, and provide easy adjustment.
Precision Dowel Pins - 316 Grade - Based on DIN7
Related Information:
Precision Dowel Pins - 303/304 Grade Stainless - Based on DIN6325, ISO2338, ISO 8734
Related Information:
Precision Dowel Pins - 303/304 Grade Stainless- Based on DIN7
Rounded end dowel pins are measured from the start of the edge rounding. This allows the pin to completely fill the hole after you grind off the rounded end. Diameter tolerances are m6. Also known as parallel pins. This category may be available in the new MBA online store at
Pins - Dowel - Standard - 303-304 Stainless - Rounded Both Ends.
Related Information:
Used for indexing and positioning of components
Once installed, it applies adequate pressure so the ball remains positioned.
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring. This category may be available in the new MBA online store at
Springs - Drawbar - Stainless Steel.
Related Information:
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100
oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at
Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
Used for close spacing and extremely tight tolerance situation.
Rc45-55 hardness. 300 grade stainless. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.
This category includes short and long lengths
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote. This category may be available in the new MBA online store at
Springs - Compression - Stainless Steel.
Related Information:
Includes series CI / VH / UR - Stainless Steel.
Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.
Includes series CE / VS / US - Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape. Ends are closed. Starting rate is the same as the kg/mm rate. This category may be available in the new MBA online store at
Springs - Compression - Conical.
Related Information:
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at
Springs - Constant Force.
Related Information:
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends. This category may be available in the new MBA online store at
Attachments - Cable - Thimbles - Stainless Steel.
Related Information:
Match with a suitable E-Clip or Circlip to suit groove size shown in listings
In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Grooved end to suit retaining clip instead of pin. This category may be available in the new MBA online store at
Pins - Clevis - Stainless Steel 300 Grade - Groove Locking.
Related Information:
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Not recommended for lifting. 304 stainless steel.
Used for locking the ends of timing belt lengths used in reciprocating applications
Suits single and double sided belts. Black Polycarbonate with 303 stainless fasteners. Low inertia. Compact Design. Patent Pending. For MXL, XL, GT 2mm, GT 3mm, GT 5mm, HTD 3mm and HTD 5mm belt pitches.
Related Information:
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened. This category may be available in the new MBA online store at
Shaftloc-tm Sleeves - Single Ended.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 1.78o Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.