Gears Metric Mitre
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Zinc Diecast.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 2 - Zinc Diecast.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1.5 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 0.5 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 3 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 1.5 - Steel.
Related Information:
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 3.5 - Steel.
POM Plastic
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 24 Diametrical Pitch - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 24 Diametrical Pitch - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 10 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 12 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle - Unhardened Steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 16 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 8 Diametrical Pitch - Steel.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Brass.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Plastic.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Plastic.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Stainless.
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.7 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Aluminium.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Stainless.
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.25 - Stainless.
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.5 - Plastic.
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1 - Plastic.
PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 3 - Plastic.
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
PCD = No. of Teeth x 0.500mm - POM Plastic
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Steel Parts: Quality class 5.8. Handle: Diecast zinc to DIN 1743 or Glass fibre reinforced plastic with toothed wheel in diecast zinc. Surface Finish: Handle plastic coated. Steel parts black oxide finish. This category may be available in the new MBA online store at
Levers - Clamp.
Handles: Die-cast zinc or plastic. Internal thread: mechanism made from carbon steel. The thru-hole clamping lever allows for quick clamping on long thread lengths. This category may be available in the new MBA online store at
Levers - Clamp - Quick Release.
Blanks for cutting gears and pulleys and friction drives.
This category may be available in the new MBA online store at
Gears - Blanks.
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 10DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 12DP - Steel.
14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 16DP - Plastic.
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 16DP - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 20 DP. Approx 3.99mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 20DP - 14.5 PA - Steel.
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 24DP - 14.5 PA - Plastic.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.