Small Parts & Bearings - an MBA company

Gears Mitre 48 Diametrical Pitch Plastic Categories


Gears Inch Mitre


Gears - Mitre - 48 Diametrical Pitch - Plastic
Gears - Mitre - 48 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
48 DP Bevel Gears
48 DP Precision Matched Sets


Gears - Mitre - 16 Diametrical Pitch - Plastic
Gears - Mitre - 16 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears - Mitre - 24 Diametrical Pitch - Plastic
Gears - Mitre - 24 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
24 DP Bevel Gears


Gears - Mitre - 32 Diametrical Pitch - Plastic
Gears - Mitre - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


You may also like

Gears Inch Bevel


Gears - Bevel - 48 Diametrical Pitch - Plastic
Gears - Bevel - 48 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
48 DP Mitre Gears


Gears - Bevel - 24 Diametrical Pitch - Plastic
Gears - Bevel - 24 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
24 DP Mitre Gears


Gears - Bevel - 32 Diametrical Pitch - Plastic
Gears - Bevel - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
32 DP Mitre Gears


Gears Inch Mitre


Gears - Mitre - 48 Diametrical Pitch - Brass
Gears - Mitre - 48 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
48 DP Bevel Gears
48 DP Precision Matched Sets


Gears - Mitre - 48 Diametrical Pitch - Steel
Gears - Mitre - 48 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
48 DP Bevel Gears
48 DP Precision Matched Sets


Gears - Mitre - 48 Diametrical Pitch - Precision Matched Sets
Gears - Mitre - 48 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Mitre Gear Sets

Sold as sets - 1:1 Ratio. Stainless steel and aluminium.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90o angle. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
48 DP Bevel Gears Precision Matched Sets


Gears Inch Bevel


Gears - Bevel - 48 Diametrical Pitch - Precision Matched Sets
Gears - Bevel - 48 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Bevel Gear Sets

Sold as sets. For 90o angle power transfer. Ratios exceeding 1 to 1.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. See Gears - Mitre for 1:1 ratios.

Related Information:
48 DP Mitre Gears Precision Matched


Gears Inch Racks


Gear Racks - 48DP - 14.5 PA - Plastic
Gear Racks -  48DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Spur


Gears - Spur - 48DP - 14.5 Degree - Plastic
Gears - Spur -  48DP - 14.5 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - 20 Degree - Plastic
Gears - Spur -  48DP - 20 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Racks


Gear Racks - 16DP - Plastic
Gear Racks -  16DP - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Spur


Gears - Spur - 48DP - 20 Degree - Plastic with Insert
Gears - Spur -  48DP - 20 Degree - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Mitre


Gears - Mitre - 24 Diametrical Pitch - Brass
Gears - Mitre - 24 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
24 DP Bevel Gears


Gears - Mitre - 32 Diametrical Pitch - Brass
Gears - Mitre - 32 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


Gears - Mitre - 10 Diametrical Pitch - Steel
Gears - Mitre - 10 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears - Mitre - 12 Diametrical Pitch - Steel
Gears - Mitre - 12 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears - Mitre - 16 Diametrical Pitch - Steel
Gears - Mitre - 16 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Unhardened Steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears - Mitre - 20 Diametrical Pitch - Steel
Gears - Mitre - 20 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Unhardened Steel.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears - Mitre - 24 Diametrical Pitch - Steel
Gears - Mitre - 24 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
24 DP Bevel Gears


Gears - Mitre - 32 Diametrical Pitch - Steel
Gears - Mitre - 32 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
32 DP Bevel Gears


Gears - Mitre - 8 Diametrical Pitch - Steel
Gears - Mitre -  8 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website


Gears Inch Racks


Gear Racks - 24DP - 14.5 PA - Plastic
Gear Racks -  24DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Mitre


Gears - Mitre - 64 Diametrical Pitch - Precision Matched Sets
Gears - Mitre - 64 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Mitre Gear Sets

Sold as sets - 1:1 Ratio. Stainless steel and aluminium.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90o angle. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
64 DP Bevel Gears Precision Matched Sets


Gears - Mitre - 72 Diametrical Pitch - Precision Matched Sets
Gears - Mitre - 72 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Mitre Gear Sets

Sold as sets - 1:1 Ratio. Stainless steel and aluminium.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90o angle. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
For simple ready selected sets of 90 degree gears please see the SPB Website
72 DP Bevel Gears Precision Matched Sets


Gears Inch Racks


Gear Racks - 32DP - 14.5 PA - Plastic
Gear Racks -  32DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.



Gears Inch Bevel


Gears - Bevel - 48 Diametrical Pitch - Brass
Gears - Bevel - 48 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
48 DP Mitre Gears


Gears - Bevel - 48 Diametrical Pitch - Steel
Gears - Bevel - 48 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
48 DP Mitre Gears


Gears Inch Spur


Gears - Spur - 48DP - Hub Mounting - Plastic with Aluminium Core
Gears - Spur -  48DP - Hub Mounting - Plastic with Aluminium Core

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Worms


Worm Gears - 24DP Series 1 - Plastic
Worm Gears - 24DP Series 1 - Plastic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 4.77o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:
Matching Plastic Worms 24 DP Series 1


Worm Gears - 32DP Series 1 - Plastic
Worm Gears - 32DP Series 1 - Plastic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:
Matching Plastic Worms 32 DP Series 1


Worm Gears - 32DP Series 2 - Plastic
Worm Gears - 32DP Series 2 - Plastic

Also see combined categories:
All Worm Gears
All Imperial Worm Gears

Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.

20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:
Matching Plastic Worms 32 DP Series 2


Gears Inch Spur


Gears - Spur - 64DP - Plastic
Gears - Spur -  64DP - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Bevel


Gears - Bevel - 64 Diametrical Pitch - Precision Matched Sets
Gears - Bevel - 64 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Bevel Gear Sets

Sold as sets. For 90o angle power transfer. Ratios exceeding 1 to 1.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. See Gears - Mitre for 1:1 ratios.

Related Information:
64 DP Mitre Gears Precision Matched


Gears - Bevel - 72 Diametrical Pitch - Precision Matched Sets
Gears - Bevel - 72 Diametrical Pitch - Precision Matched Sets

Also see combined categories:
All Imperial Bevel Gear Sets

Sold as sets. For 90o angle power transfer. Ratios exceeding 1 to 1.

Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20o Pressure Angle. See Gears - Mitre for 1:1 ratios.

Related Information:
72 DP Mitre Gears Precision Matched


Gears Inch Spur


Gears - Spur - 24DP - 14.5 Degree - Plastic
Gears - Spur -  24DP - 14.5 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system. Nylon.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Plastic
Gears - Spur -  32DP - 20 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Plastic with Insert
Gears - Spur -  64DP - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Plastic with Insert
Gears - Spur -  72DP - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 16DP - 14.5 Degree - Plastic
Gears - Spur -  16DP - 14.5 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 14.5 Degree - Plastic
Gears - Spur -  32DP - 14.5 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Plastic with Insert
Gears - Spur -  32DP - 20 Degree - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 16DP - 20 Degree - Plastic
Gears - Spur -  16DP - 20 Degree - Plastic

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon and acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Hub Mounting - Plastic with Aluminium Core
Gears - Spur -  64DP - Hub Mounting - Plastic with Aluminium Core

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Hub Mounting - Plastic with Aluminium Core
Gears - Spur -  72DP - Hub Mounting - Plastic with Aluminium Core

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 16DP - 20 Degree - Plastic with Stainless Core - Hubless
Gears - Spur -  16DP - 20 Degree - Plastic with Stainless Core - Hubless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - Hub Mounting - Plastic with Aluminium Core - No Hub
Gears - Spur -  24DP - Hub Mounting - Plastic with Aluminium Core - No Hub

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - Hub Mounting - Plastic with Aluminium Core
Gears - Spur -  32DP - Hub Mounting - Plastic with Aluminium Core

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Acetal with aluminium core. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - 14.5 Degree - Brass
Gears - Spur -  48DP - 14.5 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - 20 Degree - Brass
Gears - Spur -  48DP - 20 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Inch Bevel


Gears - Bevel - 24 Diametrical Pitch - Brass
Gears - Bevel - 24 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
24 DP Mitre Gears


Gears - Bevel - 32 Diametrical Pitch - Brass
Gears - Bevel - 32 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:
32 DP Mitre Gears


Gears Inch Spur


Gears - Spur - 48DP - 20 Degree - Steel
Gears - Spur -  48DP - 20 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - 20 Degree - Stainless
Gears - Spur -  48DP - 20 Degree - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Plastic with No Hub
Gears - Spur -  24DP - 20 Degree - Plastic with No Hub

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - 20 Degree - Aluminium
Gears - Spur -  48DP - 20 Degree - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 2024 and 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - Hub Mounting - Aluminium
Gears - Spur -  48DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - Hub Mounting - Stainless
Gears - Spur -  48DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears Cluster


Gears - Cluster - 48 Diametrical Pitch
Gears - Cluster - 48 Diametrical Pitch

Also see combined categories:
All Cluster Gears

Have a mounting area for a second gear - see diagram.

All have a 20 deg. Pressure Angle. Mounting diameter 9.525 (+0.008 / -0.000) mm (3/8 in.). Mounting area width 3.175 mm (1/8 in.). See diagram for mounting position of second gear. Combine with a gear from the listings under Gears - Spur . - Hub Mounting.



Gears Inch Internal








Pinion Wire Imperial


Gears - Pinion Wire - 48 Diametrical Pitch
Gears - Pinion Wire - 48 Diametrical Pitch

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.



Gears Inch Spur


Gears - Spur - 64DP - Brass
Gears - Spur -  64DP - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Stainless
Gears - Spur -  64DP - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Stainless
Gears - Spur -  72DP - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 120DP - Hub Mounting - Aluminium
Gears - Spur - 120DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 120DP - Hub Mounting - Stainless
Gears - Spur - 120DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 16DP - 14.5 Degree - Steel
Gears - Spur -  16DP - 14.5 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 14.5 Degree - Brass
Gears - Spur -  24DP - 14.5 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 14.5 Degree - Brass
Gears - Spur -  32DP - 14.5 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Brass
Gears - Spur -  32DP - 20 Degree - Brass

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Aluminium
Gears - Spur -  64DP - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Hub Mounting - Aluminium
Gears - Spur -  64DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 64DP - Hub Mounting - Stainless
Gears - Spur -  64DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Aluminium
Gears - Spur -  72DP - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Hub Mounting - Aluminium
Gears - Spur -  72DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 72DP - Hub Mounting - Stainless
Gears - Spur -  72DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 80DP - Hub Mounting - Aluminium
Gears - Spur -  80DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 80DP - Hub Mounting - Stainless
Gears - Spur -  80DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 96DP - Hub Mounting - Aluminium
Gears - Spur -  96DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB WebsiteFor simple ready selected sets of rack and gear please see the HES website


Gears - Spur - 96DP - Hub Mounting - Stainless
Gears - Spur -  96DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB WebsiteFor simple ready selected sets of rack and gear please see the HES website


Gears - Spur - 24DP - 14.5 Degree - Steel
Gears - Spur -  24DP - 14.5 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system. Carbon Steel.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - Hub Mounting - Aluminium
Gears - Spur -  24DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 14.5 Degree - Steel
Gears - Spur -  32DP - 14.5 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Aluminium
Gears - Spur -  32DP - 20 Degree - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Steel
Gears - Spur -  32DP - 20 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. Carbon Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - Hub Mounting - Aluminium
Gears - Spur -  32DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - Hub Mounting - Stainless
Gears - Spur -  24DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - 20 Degree - Stainless
Gears - Spur -  32DP - 20 Degree - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 32DP - Hub Mounting - Stainless
Gears - Spur -  32DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
Gear Hubs to Suit
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Aluminium
Gears - Spur -  24DP - 20 Degree - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Steel
Gears - Spur -  24DP - 20 Degree - Steel

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 24DP - 20 Degree - Stainless
Gears - Spur -  24DP - 20 Degree - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

Plastic and metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Gears - Spur - 48DP - Stem - Stainless
Gears - Spur -  48DP - Stem - Stainless

Also see combined categories:
All Imperial Spur Gears
All Imperial Stem Gears

303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:
For simple ready selected sets of spur gears please see the SPB Website


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts & Bearings offers 126286 products in 2931 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts & Bearings offers 126286 products in 2931 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.