Pins Dowel
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Gears Metric Bevel
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
Gears Metric Mitre
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 0.5 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1.5 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 3 - Plastic.
Related Information:
Gears Metric Spur
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Brass.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Plastic.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Plastic.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Stainless.
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.7 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Aluminium.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Stainless.
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.25 - Stainless.
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.5 - Plastic.
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1 - Plastic.
PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 3 - Plastic.
Gears Metric Mitre
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Zinc Diecast.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 2 - Zinc Diecast.
Related Information:
Gears Metric Spiral Mitre
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 1.5 - Steel.
Related Information:
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 3.5 - Steel.
Gears Metric Spur
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Gears Metric Worms
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
You may also be interested in
Couplings Helical and Slit
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5
o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at
Couplings - Helical - Economy.
Related Information:
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5
o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at
Couplings - Helical - Standard.
Related Information:
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Related Information:
Aluminium - Flexible.
Cable
Use with synchromesh or standard miniature cable
Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).
Related Information:
Pins Taper
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Related Information:
Metric Sizes Tapered 1:50 and threaded externally for easy extraction.
Related Information:
Metric Sizes Tapered 1:50 and threaded internally for easy extraction.
Related Information:
Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um
Related Information:
Leadscrews
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
Related Information:
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
Related Information:
Springs Die
Colour coded yellow
High tensile strength chromium alloy steels. Heat Resistance: Up to +230
oC (Loss of load occurs above +120
oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at
Springs - Die - Metric - Extra Heavy Duty.
Related Information:
Colour coded red
High tensile strength chromium alloy steels. Heat Resistance: Up to +230
oC (Loss of load occurs above +120
oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at
Springs - Die - Metric - Heavy Duty.
Related Information:
Colour coded green
High tensile strength chromium alloy steels. Heat Resistance: Up to +230
oC (Loss of load occurs above +120
oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at
Springs - Die - Metric - Light Duty.
Related Information:
Colour coded blue
High tensile strength chromium alloy steels. Heat Resistance: Up to +230
oC (Loss of load occurs above +120
oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length. This category may be available in the new MBA online store at
Springs - Die - Metric - Medium Duty.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138616
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.