Small Parts & Bearings - an MBA company

Searched for: Gears cluster module 0.5 brass categories


Gears Cluster


Gears - Cluster - Module 0.5 - Brass
Gears - Cluster - Module 0.5 - Brass

Also see combined categories:
All Cluster Gears
All Hobby Gears

This category may be available in the new MBA online store at Gears - Cluster - Module 0.5 - Brass.


You may also be interested in

Gears Metric Mitre


Gears - Mitre - Module 0.5 - Plastic
Gears - Mitre - Module 0.5 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Plastic.

Related Information:


Gears Metric Spur


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic.


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.


Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.


Hobby Gears


Gears - Mitre - Module 0.5 - Hobby - Economy - Plastic
Gears - Mitre - Module 0.5 - Hobby - Economy - Plastic

Also see combined categories:
All Metric Mitre Gears
All Hobby Gears

POM Plastic

Plastic Only. Inexpensive for hobby and toy use. No locking mechanisms. This category may be available in the new MBA online store at Gears - Mitre - Module 0.5 - Hobby - Economy - Plastic.


Gears - Crown Wheel - Module 0.5 - Hobby - Plastic
Gears - Crown Wheel - Module 0.5 - Hobby - Plastic

Also see combined categories:
All Hobby Gears

PCD = No. of Teeth x 0.500mm - POM Plastic

Plastic Only. Inexpensive for hobby and toy use. No locking mechanisms. This category may be available in the new MBA online store at Gears - Crown Wheel - Module 0.5 - Hobby - Plastic.


Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1.5 - Brass.

Related Information:


Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Brass.

Related Information:


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.


Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1.5 - Plastic.

Related Information:


Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - Module 1 - Plastic.

Related Information:


Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Plastic.

Related Information:


Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Module 1 - Zinc Diecast.

Related Information:


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic.


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic.


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.


Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.


Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Also see combined categories:
All Module 1.25 Spur Gears
All Metal Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.


Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Also see combined categories:
All Module 1.5 Spur Gears
All Plastic Module 1.5 Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic.


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic.


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.


Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand
Worm Gears - Module 1.5 Series 3 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:


Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 1.5 - Steel.

Related Information:


Gears - Mitre - Spiral - Module 3.5 - Steel
Gears - Mitre - Spiral - Module 3.5 - Steel

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - Spiral - Module 3.5 - Steel.


Gears - Mitre - 24 Diametrical Pitch - Brass
Gears - Mitre - 24 Diametrical Pitch - Brass

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 24 Diametrical Pitch - Brass.

Related Information:


Gears - Spur - 24DP - 14.5 Degree - Brass
Gears - Spur -  24DP - 14.5 Degree - Brass

Also see combined categories:
All 24DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 14.5 Degree - Brass.


Gears - Spur - 32DP - 14.5 Degree - Brass
Gears - Spur -  32DP - 14.5 Degree - Brass

Also see combined categories:
All 32DP Spur Gears 14.5 Degree

PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 32DP - 14.5 Degree - Brass.


Gears - Pinion Wire - 32 Diametrical Pitch
Gears - Pinion Wire - 32 Diametrical Pitch

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gears - Pinion Wire - 32 Diametrical Pitch.


Slides - Linear - Clean Room
Slides - Linear - Clean Room

Also see combined categories:
All Linear Slides

Stainless Steel throughout (similar to 440C). Speed: 0.5 m/sec (30 m/min). Temperature: +100oC (Continuous), +140oC (Maximum). Life will be less than normal at +100oC and dimensions may change. Lateral Loading: Dynamic x 1.13 C - Static x 1.19 Co. Precision Linear Slide Unit is a compact linear motion rolling guide for limited stroke length.


Gears - Spur - 24DP - 20 Degree - Plastic - Plain
Gears - Spur -  24DP - 20 Degree - Plastic - Plain

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic - Plain.


Gears - Spur - 24DP - 20 Degree - Plastic with Insert
Gears - Spur -  24DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 24DP Spur Gears 20 Degree
All 24DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 1.058mm (1/24 in.). 20o Pressure Angle. Acetal or Nylon w/ Brass or Stainless Steel Inserts. Clamping or Grub Screw hubs. DP stands for Diametrical Pitch and is an imperial measurement system. Clamping and grub screw type.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 20 Degree - Plastic with Insert.


Gears - Spur - 48DP - 20 Degree - Aluminium
Gears - Spur -  48DP - 20 Degree - Aluminium

Also see combined categories:
All 48DP Spur Gears 20 Degree
All 48DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 2024 and 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Aluminium.


Gears - Spur - 48DP - 20 Degree - Plastic
Gears - Spur -  48DP - 20 Degree - Plastic

Also see combined categories:
All 48DP Spur Gears 20 Degree
All 48DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Plastic.


Gears - Spur - 48DP - 20 Degree - Stainless
Gears - Spur -  48DP - 20 Degree - Stainless

Also see combined categories:
All 48DP Spur Gears 20 Degree
All 48DP Spur Gears 20 Degree Metal

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Stainless.


Gears - Spur - 48DP - 20 Degree - Plastic with Insert
Gears - Spur -  48DP - 20 Degree - Plastic with Insert

Also see combined categories:
All 48DP Spur Gears 20 Degree
All 48DP Spur Gears 20 Degree Plastic

PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. Acetal and Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Plastic with Insert.


Slides - Linear - Non Recirculating Ball - Standard
Slides - Linear - Non Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.


Slides - Linear - Recirculating Ball - Standard
Slides - Linear - Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.


Bushes - Brass - Graphite Plug - Flanged
Bushes - Brass - Graphite Plug - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

High-Tensile Brass Alloy. Suitable for use under conditions of heavy load and low speed operation. Solid Lubricant Plugs. Excellent wear resistance can be exerted at parts with reciprocating motion, frequent starting and stopping, etc., where oil film is difficult to form. Class 7 precision ID. 29N per mm sq max allowable load with max allowable speed 0.5m per second unlubricated and 1m per second lubricated.

Related Information:


Bushes - Brass - Graphite Plug - Unflanged
Bushes - Brass - Graphite Plug - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. Brass Alloy.

High-Tensile Brass Alloy. Suitable for use under conditions of heavy load and low speed operation. Solid Lubricant Plugs. Excellent wear resistance can be exerted at parts with reciprocating motion, frequent starting and stopping, etc., where oil film is difficult to form. Class 7 precision ID. 29N per mm sq max allowable load with max allowable speed 0.5m per second unlubricated and 1m per second lubricated.

Related Information:


Gears - Blanks
Gears - Blanks


Blanks for cutting gears and pulleys and friction drives.

This category may be available in the new MBA online store at Gears - Blanks.


Gear Racks - Flexible
Gear Racks - Flexible

Also see combined categories:
All Flexible Gear Racks

Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.

20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.


Gears - Bevel - 32 Diametrical Pitch - Plastic
Gears - Bevel - 32 Diametrical Pitch - Plastic

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. This category may be available in the new MBA online store at Gears - Bevel - 32 Diametrical Pitch - Plastic.

Related Information:


Gears - Mitre - 10 Diametrical Pitch - Steel
Gears - Mitre - 10 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 10 Diametrical Pitch - Steel.


Gears - Mitre - 12 Diametrical Pitch - Steel
Gears - Mitre - 12 Diametrical Pitch - Steel

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Carbon steel

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at Gears - Mitre - 12 Diametrical Pitch - Steel.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.