Permanent Magnet.
Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. This category may be available in the new MBA online store at
Clutches - Slip - Magnetic Particle - No Power.
Requires no power.
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications. This category may be available in the new MBA online store at
Gearmotors - Basic - Hobby - 12.1mm Diameter.
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Housing : Plastic / Shaft : Steel. This category may be available in the new MBA online store at
Gearmotors - DC - Low Voltage.
12mm Gearhead Body Diameter.
25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive - Flanged.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Hex Drive - Standard.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Threaded inserts are screwed into pre-formed or pre-drilled holes and cut their own threads. Perfect for permanent installations.
Made from brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole. This category may be available in the new MBA online store at
Inserts - Self Tapping - For Wood - Slotted Drive - Short.
Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.
The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout. This category may be available in the new MBA online store at
Inserts - Tapered Fit - Finserts - For Wood and Plastics.
Supplied with keeper
No keepers
No keepers
General purpose horseshoe magnet
Supplied with keeper
Alnico sintered ASA 8HC
Related Information:
Cast Alnico 5 bar
Supplied with keeper
Extended poles can be lightly machined. Press fit. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Ideal for hanging signs and lights, retrieving steel items from tanks, vats, bins etc.
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73
oC to 93
oC. Size tolerances +/- 0.13. This category may be available in the new MBA online store at
Magnets - Rare Earth - Plated.
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures. This category may be available in the new MBA online store at
Magnets - Rare Earth - Shielded.
Magnetic Vinyl Sheets and Magnetic Rubber Strip
Please note that ball magnets are not to be used as toys. These are a strong magnet must be kept away from children as serious harm may result from ingestion.
Related Information:
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from 316 Stainless Steel - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from Ground Glass - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
Various styles - refer pictures
Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153543
products in 2089 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.