Gearmotors Permanent Magnet Categories
Gearmotors - DC PM - Size 70x114
Permanent Magnet.
Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.
Clutches - Slip - Magnetic Particle - No Power
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
Related Information:
Clutches - Slip - Magnetic Particle - Integral Shaft - No Power
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
Related Information:
Gearmotors - Basic - Hobby - 12.1mm Diameter
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
Gearmotors - DC - Low Voltage
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Housing : Plastic / Shaft : Steel.
Gearmotors - DC - Size 25 Low Cost
25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible
D Shaped 4x8mm Output Shaft.
Gearmotors - Open Gear
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
Tape - Silicone Wrap
Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive. Supa Tape.
Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 oC to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.
Inserts - Self Tapping - For Plastics - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Inserts - Self Tapping - For Plastics - Stainless Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Inserts - Self Tapping - For Wood - Hex Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Inserts - Self Tapping - For Wood - Slotted Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Inserts - Self Tapping - For Wood - Slotted Drive - Short
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.
Inserts - Tapered Fit - Finserts - For Wood and Plastics
Finserts provide strong metal threads in wood, composition board and thermoplastics such as nylon, polystyrene, cellulose acetate and cycolac. By distributing stress over a greater surface area, firm permanent fastening is ensured.
The fins give higher holding strength in softer materials. Available with one, two or three fins for varying material thickness. Finserts prevent splintering, splitting and thread pullout.
Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit
Extended poles can be lightly machined. Press fit. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole
Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Magnets - Ceramic Blocks
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Magnets - Ceramic Cylinder
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Magnets - Cup Assemblies - Loop
Ideal for hanging signs and lights, retrieving steel items from tanks, vats, bins etc.
Plated cup with a 9.525mm ID loop.
Magnets - Rare Earth - Plated
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 oC to 93 oC. Size tolerances +/- 0.13.
Magnets - Rare Earth - Shielded
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures.
Catches - Magnetic - Ultra Thin - Heavy Duty
Ultra thin strong magnetic catch is perfect for tight areas. Has a full 4kg of magnetic force.
Related Information:
Catches - Magnetic - Ultra Thin - Light Duty
Ultra thin strong magnetic catch is perfect for tight areas. Has 2.5 kg of magnetic force.
Related Information:
Clutches - Magnetic Particle 24VDC
Ultrafast Responses.
The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start.
Related Information:
Balls - Stainless Steel - 304 Grade
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.
Related Information:
Balls - Stainless Steel - 316 Grade
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.
Related Information:
Bearings - Ceramic Si3N4 - Radial
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02. Full ceramic silicon nitride.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls and rings. HRC80 Hardness. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.
Related Information:
Bearings - Ceramic ZrO2 - Radial
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed. Full ceramic zirconia.
Applications include cryopumps, medical applications, semiconductors, turbine flow meters, food processing, robotics and optics. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 oC with PTFE Cage and 130 Deg C with Nylon Cage.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127030 products in 2370 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
