Small Parts & Bearings - an MBA company

Gearmotors basic hobby 12.1mm diameter categories


Gearmotors Basic


Gearmotors - Basic - Hobby - 12.1mm Diameter
Gearmotors - Basic - Hobby - 12.1mm Diameter

Also see combined categories:
All Basic Gearmotors

Small light weight geared motors used in toys and small solar applications

NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.

You may also like to check if Hobby and Engineering Supplies list a range of Gearmotors - Basic - Hobby - 12.1mm Diameter.


Gearmotors - DC - Size 12
Gearmotors - DC - Size  12

Also see combined categories:
All DC Gearmotors

12mm Gearhead Body Diameter.



Gearmotors - DC - Size 25 Low Cost
Gearmotors - DC - Size  25 Low Cost


25mm Gearhead Body Diameter. 24.4mm Motor Body Diameter. Low cost. Reversible

D Shaped 4x8mm Output Shaft.


Rod - Round - Urethane
Rod - Round - Urethane

Also see combined categories:
All Non Metallic Rod - Round

Hard urethane rubber compound. Machinable.

Length +/- 3.2mm. Diameter +/- 2 percent.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Rod - Round - Urethane.


Pulleys - Geared - Hobby
Pulleys - Geared - Hobby

Also see combined categories:
All Flat Belt Pulleys

Small UPE grooved pulleys suitable for driving small o'rings or rubber bands. O-rings should be less than 2mm section diameter.


You may also like to check if Hobby and Engineering Supplies list a range of Pulleys - Geared - Hobby.


Snap Rings - External - Basic
Snap Rings - External - Basic

Also see combined categories:
All External Snaprings

Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.

Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment.


Rod - Round - Nylon
Rod - Round - Nylon

Also see combined categories:
All Plastic Rod

High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Rod - Round - Nylon.


Hobby Gears - Spur - 48DP
Hobby Gears - Spur - 48DP


A small selection of popular 48DP Plastic/ Metal Pinion and Spur gears

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a 48DP spur gear, divide multiply the no of teeth by 0.52917.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Hobby Gears - Spur - 48DP.


Rod - Round - Polyester PETP
Rod - Round - Polyester PETP

Also see combined categories:
All Plastic Rod

High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Rod - Round - Polyester PETP.


Rod - Round - PTFE
Rod - Round - PTFE

Also see combined categories:
All Plastic Rod

Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Rod - Round - PTFE.


Snap Rings - Internal - Basic
Snap Rings - Internal - Basic

Also see combined categories:
All Internal Snaprings

M2300 / SB / ESB Snaprings. Like an internal circlip without the lugs.

Applications include gear systems, securing needle bearings and to act as spacers. Used on the inside bore diameter of a housing or similar.


Hobby Gears - Spur - Module 0.4
Hobby Gears - Spur - Module 0.4


A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Hobby Gears - Spur - Module 0.4.


Hobby Gears - Spur - Module 0.5
Hobby Gears - Spur - Module 0.5


A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Hobby Gears - Spur - Module 0.5.


Rod - Round - Acetal
Rod - Round - Acetal

Also see combined categories:
All Plastic Rod

Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Rod - Round - Acetal.


Rod - Round - Sintered Bronze
Rod - Round - Sintered Bronze

Also see combined categories:
All Metal Rod - Round

Sintered bronze rod is supplied oversized so it can be machine finished to the dimensions shown.

Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight. B438 grade 1, Type 2 - AMS4805-D. SAE 841 Type 1, Class A.

Related Information:


Gearmotors - DC - Low Voltage
Gearmotors - DC - Low Voltage

Also see combined categories:
All Low Voltage DC Gearmotors

Reversible - Low Voltage - Self Starting.

Reversible. Low Voltage. Self Starting. Housing : Plastic / Shaft : Steel.

You may also like to check if Hobby and Engineering Supplies list a range of Gearmotors - DC - Low Voltage.


Gearmotors - Open Gear
Gearmotors - Open Gear


Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.


You may also like to check if Hobby and Engineering Supplies list a range of Gearmotors - Open Gear.


Gearmotors - DC PM - Size 70x114
Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.


Motors - DC 6mm Diameter
Motors - DC  6mm Diameter

Also see combined categories:
All DC Motors

Our smallest motors at an affordable price.

Various models 10000 to 30000 rpm. Low starting voltage of Less than0.8V. Rated Voltage 1.3V. Less than 43 dB Mechanical Noise Level. 100 hours / 100000 turns mechanical life. Clockwise rotation when viewed from shaft end. Not recommended for reversing.

Related Information:

You may also like to check if Hobby and Engineering Supplies list a range of Motors - DC 6mm Diameter.


Switches - Rocker
Switches - Rocker

Also see combined categories:
All Switches

20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.

Switchs are rated at 10amp @ 600VAC with finger safe screw terminals.

You may also like to check if Hobby and Engineering Supplies list a range of Switches - Rocker.


Rollers - Drive
Rollers - Drive

Also see combined categories:
All Rollers

Neoprene 60 durometer black ground outside diameter drive rollers



Bearings - Spherical OD
Bearings - Spherical OD


Bearings with a spherical outside diameter.

Combined listing of spherical OD track rollers and bearings for Linear Guide systems.

Related Information:


Rollers - Feed - With Aluminium Sleeve
Rollers - Feed - With Aluminium Sleeve

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Related Information:


Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:


Couplings - Reli-a-flex - Long Series - Clamp Type
Couplings - Reli-a-flex - Long Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Couplings - Reli-a-flex - Short Series - Clamp Type
Couplings - Reli-a-flex - Short Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - DIN7

Diameter tolerances are m6. Also known as parallel pins.

Related Information:


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Bearings - One Way - Roller
Bearings - One Way - Roller

Also see combined categories:
All One Way Clutch Bearings

Roller Clutch Bearings rotate in one direction only.

Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.

Related Information:


Rings - Retaining - C Type External - For Linear Bearings
Rings - Retaining - C Type External - For Linear Bearings


Fits into the retaining ring grooves on the outside diameter of Super Smart, Super and Precision Linear Bearings to provide external mounting retension.



Gears - Spur - 120DP - Hub Mounting - Aluminium
Gears - Spur - 120DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 120DP - Hub Mounting - Stainless
Gears - Spur - 120DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 120 Diametrical Pitch. Approx 0.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - Hub Mounting - Aluminium
Gears - Spur -  24DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 24DP - Hub Mounting - Stainless
Gears - Spur -  24DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 24 Diametrical Pitch. Approx 3.33mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - Hub Mounting - Aluminium
Gears - Spur -  32DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 32DP - Hub Mounting - Stainless
Gears - Spur -  32DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 32 Diametrical Pitch. Approx 2.49mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - Hub Mounting - Aluminium
Gears - Spur -  48DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 48DP - Hub Mounting - Stainless
Gears - Spur -  48DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 48 Diametrical Pitch. Approx 1.66mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 64DP - Hub Mounting - Aluminium
Gears - Spur -  64DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 64DP - Hub Mounting - Stainless
Gears - Spur -  64DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 64 Diametrical Pitch. Approx 1.25mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 72DP - Hub Mounting - Aluminium
Gears - Spur -  72DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 72DP - Hub Mounting - Stainless
Gears - Spur -  72DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 80DP - Hub Mounting - Aluminium
Gears - Spur -  80DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 80DP - Hub Mounting - Stainless
Gears - Spur -  80DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 80 Diametrical Pitch. Approx 1mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 96DP - Hub Mounting - Aluminium
Gears - Spur -  96DP - Hub Mounting - Aluminium

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 96DP - Hub Mounting - Stainless
Gears - Spur -  96DP - Hub Mounting - Stainless

Also see combined categories:
All Imperial Spur Gears
All Spur Gears

Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. DP stands for Diametrical Pitch and is an imperial measurement system.

Plastic and metallic. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Tube - Round - Acrylic
Tube - Round - Acrylic

Also see combined categories:
All Non Metallic Tube - Round

Acrylic Transparent Tube

Acrylic also called Poly Methyl Methacrylate (PMMA) is a transparent thermoplastic often used as light weight or shatter-resistant alternatives to glass. Acrylic is an economical alternative to polycarbonate when extreme strength is not necessary. Additionally, doesn't contain potentially harmful bisphenol-A subunits. Often preferred because of moderate properties, easy handling and processing and low cost. Acrylic in the form off tubes affords hatter resistant panels for making rotating shafts, spacers, display and many other applications. Please note this item is not a precision item. The inside diameter is not toleranced and may vary between batches.

You may also like to check if Hobby and Engineering Supplies list a range of Tube - Round - Acrylic.


Extenders - Shaft
Extenders - Shaft


Miniature and large shaft extenders and reducers. Used to increase or reduce the diameter, or increase the length of shafts.

Also known as shaft increasers or shaft reducers.

Related Information:


Mounts - Leveling - Stud Type - Stainless Steel - Imperial
Mounts - Leveling - Stud Type - Stainless Steel - Imperial

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. 303 stainless steel. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.


Mounts - Leveling - Stud Type - Stainless Steel - Metric
Mounts - Leveling - Stud Type - Stainless Steel - Metric

Also see combined categories:
All Pivotal Levelers
All Mounting Feet

Good quality with value pricing. 303 stainless steel. Adjusters.

Large diameter base for added support. 15o off centre swivel for quick leveling on sloped surfaces.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124370 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.