Gearmotors Open
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
You may also be interested in
Gearboxes Cross Axis
Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Related Information:
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Related Information:
Used for locking the ends of timing belt lengths used in linear applications
Suits single sided belts only. Aluminium. Screws, hex nuts and washers included. This category may be available in the new MBA online store at
Clamp Kits - Timing Belt.
Related Information:
Clevis Pins - Keysteel - Rivet Nuts - Rivets - Shim - Screws - U Cushions - Taper Pins - Tubing - Washers
Also known as keenserts.
Related Information:
Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Contains a selection of E-Z Lok inserts
Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.
Related Information:
Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
90o clockwise rotation. Made of weatherable black nylon handle and steel parts. Includes one key. All locks keyed alike. May be used with rod kit for 2 point locking.
Related Information:
Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.
Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer. This category may be available in the new MBA online store at
Inserts - Thread Repair - Keylocking Starter Sets.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
Related Information:
Blanks for cutting gears and pulleys and friction drives.
This category may be available in the new MBA online store at
Gears - Blanks.
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 10 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 12 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle - Unhardened Steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 16 Diametrical Pitch - Steel.
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 24 Diametrical Pitch - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 24 Diametrical Pitch - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle - Carbon steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - 8 Diametrical Pitch - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 10DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 12DP - Steel.
14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 16DP - Plastic.
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 16DP - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 20 DP. Approx 3.99mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 20DP - 14.5 PA - Steel.
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 24DP - 14.5 PA - Plastic.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 24DP - Stainless.
14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 32DP - 14.5 PA - Plastic.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 32DP - Stainless Steel.
14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 48DP - 14.5 PA - Plastic.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 48DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 64 DP. Approx 1.25mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 64DP - Stainless.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 6 DP. Approx 13.3mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 6DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 8 DP. Approx 9.98mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 8DP - 14.5 PA - Steel.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 96 DP. Approx 0.83mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless - Side Holes.
PCD = No. of Teeth x 2.540mm (1/10 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.
PCD = No. of Teeth x 2.117mm (1/12 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 16DP - 14.5 Degree - Steel.
PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon and acetal. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 16DP - 20 Degree - Plastic.
PCD = No. of Teeth x 1.270mm (1/20 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at
Gears - Spur - 24DP - 14.5 Degree - Brass.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.