Gears Metric Spiral Mitre
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 1.5 - Steel.
Related Information:
1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.
A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Spiral - Module 3.5 - Steel.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Stainless.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Stainless.
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.25 - Stainless.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 12DP - Steel.
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 16DP - Steel.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 32DP - Stainless Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 10DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 20 DP. Approx 3.99mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 20DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 6 DP. Approx 13.3mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 6DP - 14.5 PA - Steel.
14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 8 DP. Approx 9.98mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 8DP - 14.5 PA - Steel.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 24DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 48DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 64 DP. Approx 1.25mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 64DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 96 DP. Approx 0.83mm between teeth. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at
Gear Racks - 96DP - Stainless - Side Holes.
Imperial and Metric / Carbon Steel. Also known as Heim Joints
Bearing Steel, hardened, ground and chromium plated Inner ring, Heavy duty bronze with embedded bronze - PTFE fabric Outter ring. Steel/Bronze - PTFE fabric Sliding Combination. Also known as Heim Joints
Bearing Steel, hardened, ground and chromium plated Inner ring, Heavy duty bronze with embedded bronze - PTFE fabric Outter ring. Steel/Bronze - PTFE fabric Sliding Combination.
Imperial and Metric / Carbon Steel. Also known as Heim Joints
Also known as Heim Joints
Also known as Heim Joints
Dimensions not shown are available on request.
Spyraflo sintered bronze bearing in a special self-clinching steel housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsuis. Maximum Load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Composite bearing material conisting of 3 bonded layers; Steel backing bonded with porous sintered bronze interlayer which is impregnated and overlaid with polytetrafluroethylene (PTFE). Lead free.
Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Requires No lubrication, provides maintenance free operation. Exhibits low wear rate, Seizure resistant. High Static and Dynamic Load capacity, Good frictional properties with negligible stick-slip. Resists Solvents, Compact and light. No water Absorption, Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments. Good embedability and is tolerant of dusty environments. Speed Limit in oil 5 metres surface speed per second.
Related Information:
Plastic, bronze and steel.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 6.90o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match.
20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
For 90o angle power transfer. Ratios exceeding 1 to 1.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 0.5 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1.5 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Brass.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Plastic.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 1 - Zinc Diecast.
Related Information:
1:1 Ratio. 20o Pressure Angle
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 2 - Zinc Diecast.
Related Information:
1:1 Ratio. 20o Pressure Angle - Acetal
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90
o angle. See Gears - Bevel for other ratios. This category may be available in the new MBA online store at
Gears - Mitre - Module 3 - Plastic.
Related Information:
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Brass.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.4 - Plastic.
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.5 - Plastic.
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.7 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Aluminium.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 0.8 - Plastic.
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
Fairloc
TM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Gears - Spur - Module 1.5 - Plastic.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.