Small Parts & Bearings - an MBA company

Friction Grip Yoshida Parts Categories


Dental Handpiece Parts


Friction Grip Yoshida Parts
Friction Grip Yoshida Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


639A Friction Grip Kavo Parts
639A Friction Grip Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Black Pearl Friction Grip Bien Air Parts
Black Pearl Friction Grip Bien Air Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Push Button Yoshida Parts
Push Button Yoshida Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.




Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.


Torches
Torches


Includes hands free and friction recharge types and night vision preservation


Related Information:


Clutches - Slip - Inline
Clutches - Slip - Inline

Also see combined categories:
All Slip Clutches

Multiplate Design.

Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.

Related Information:


Bushes - Plastic - X-Lube - Flanged
Bushes - Plastic - X-Lube - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Self lubricating - low friction - non-corrosive - light weight - chemical resistant.

Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Gears - Blanks
Gears - Blanks


Blanks for cutting gears and pulleys and friction drives.



Rod - Round - PTFE
Rod - Round - PTFE

Also see combined categories:
All Plastic Rod

Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Linear - Assemblies - Ball Slide - Precision
Linear - Assemblies - Ball Slide - Precision


These precision ball slides have a typical coefficient of friction of 0.003 and provide straight line accuracy of 0.0005mm per mm of travel.

At load capacity a life of 250 million mm of travel can be expected. The expected life at half load capacity is 2.5 billion mm. Factory preload adjustment prevents sideplay and backlash. Lightweight aluminium carriage and base with high load capacity. Four tapped and threaded carriage holes and counterbored base holes simplify installation and component mounting. Long life, self cleaning ball bearing needs no lubrication. Positional repeatability 0.005mm. Clear anodised finish.


Wheels - Industrial - Plastic - Solid
Wheels - Industrial - Plastic - Solid

Also see combined categories:
All Wheels

Wheel loadings include a safety factor of 3. Low noise. Low friction.

Related Information:


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


O-Rings - Quad
O-Rings - Quad

Also see combined categories:
All O-Rings

Quadrings or quattrorings reduce the amount of squeeze needed for positive seal, reducing friction and extending seal life.

Temperature Range: -30oC to +90oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Also known as quad rings.

Related Information:


Washers - Self Aligning - Sets - Plastic
Washers - Self Aligning - Sets - Plastic

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.

Related Information:


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.


Wheels - Industrial - Plastic - Rubber Tyred
Wheels - Industrial - Plastic - Rubber Tyred

Also see combined categories:
All Wheels

Suitable for lawn mowers, trolleys, carts etc

Wheel loadings include a safety factor of 3. Low noise. Low friction.

Related Information:


Ball Slides - Crossed Roller Positioning Stages
Ball Slides - Crossed Roller Positioning Stages


Used for Gauging and Positioning Light to Medium Loads.

Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Positioning Slides can be stacked for Multi axis applications. Preloaded positioning slides fully assemebled. Black Anodized Finish.


Linear Slides - Cross Roller Tables - Aluminium
Linear Slides - Cross Roller Tables - Aluminium

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Cross Roller Tables - Steel
Linear Slides - Cross Roller Tables - Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Low Profile - Crossed Roller Table - Aluminium
Linear Slides - Low Profile - Crossed Roller Table - Aluminium

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Washers - Nord Lock - Zinc Plated
Washers - Nord Lock - Zinc Plated

Also see combined categories:
All Serrated Locking Washers
All Lock Washers

Supplied in pairs

Steel: Hardness HRA 75+/-3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer. Also see Lockrite and Disc Lock washers.

Related Information:


Linear Guide System - Low Profile - Size 17
Linear Guide System - Low Profile - Size 17

Also see combined categories:
All Linear Slides

Carriage Assembly and Rails sold separately. Listed in the same category.

Low-Load applications. Max load 50N. Self Lubricating. Corrosion Resistant. Low Friction. Max Speed 15 m/s. Operating Temp -40o to 90o Celius.


ISO-PAD - Sheets
ISO-PAD - Sheets

Also see combined categories:
All ISO-PADS

For shimming and mounting machinery bases to isolate vibration.

Orange in colour. Patterned and unpatterned types. Tough vinyl chloride elastomeric resin bonded to both sides of a core of monofilament fibreglass. Co-efficient of friction 0.8. Temp range -35 oC to 110 Deg C.


Rollers - Urethane - Lengths
Rollers - Urethane - Lengths

Also see combined categories:
All Tyred OD Bearings
All Rollers

Low cost alternative for making your own wheels, castors, rollers, sheaves etc. Urethane rod with dual hardness. Harder inner sleeve with softer outside for use as a roller.

Blue outer tyre 90A Durometer bonded to a hard brown 75D Durometer inner sleeve. This results in a hard anti friction bearing surface inside with a soft tyre outside. The roller can be cut and machined to suit your purposes. Testing for your application is recommended.

Related Information:


Washers - Thrust - DP4 Type
Washers - Thrust - DP4 Type

Also see combined categories:
All Thrust Washers

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.


Linear Slide - Drylin - Carriage Assembly
Linear Slide - Drylin - Carriage Assembly

Also see combined categories:
All Linear Slides

Insensitive to dust and dirt. Match with Drylin Rail sold seperately.

Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.

Related Information:


Linear Slide - Drylin - Rail
Linear Slide - Drylin - Rail

Also see combined categories:
All Linear Slides

Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.

Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.

Related Information:


Bushes - Steel - DP4 - Split - Flanged
Bushes - Steel - DP4 - Split - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. Speed Limit in oil 3 metres surface speed per second.

Related Information:


Bushes - Steel - DP4 - Split - Unflanged
Bushes - Steel - DP4 - Split - Unflanged

Also see combined categories:
All Steel Bushes
All Unflanged Steel Bushes

Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.

Operating Temperature -200o to 280o Celsius. Maximum load 250N/mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. Speed Limit in oil 3 metres surface speed per second.

Related Information:


Rod - Round - Nylon
Rod - Round - Nylon

Also see combined categories:
All Plastic Rod

High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.

Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.

Related Information:


Parts Boxes - Clear Plastic
Parts Boxes - Clear Plastic

Also see combined categories:
All Parts Boxes

Plastics clear compartmented parts boxes with flip lids.

Plastic hinged lid. Quality catch to secure contents. Ideal for storing small parts. Includes Fischer brand and others. Also includes a small membrane box for displaying small items like coins or jewellery.


Parts Boxes - Grey Plastic
Parts Boxes - Grey Plastic

Also see combined categories:
All Parts Boxes

Fischer Plastics grey parts boxes with adjustable dividers and open top.

Open top. Fits most standard shelving. Ideal for storing small parts. Dividers can be removed, added or adjusted. Comes with dividers to make number of compartments shown - but additional dividers can be purchased.


Dubro by part number Dubro Parts
Dubro by part number Dubro Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


TT600 Yamaha Parts
TT600 Yamaha Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


1000 Midwest Parts
1000 Midwest Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


105 MTC Parts
105 MTC Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


10C Kavo Parts
10C Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124481 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124481 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.