Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at
Shafts - Flexible - Coupling Ends - Open - Mild Steel.
Related Information:
You may also be interested in
Shafting General Purpose
Couplings Other
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
Related Information:
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.
Related Information:
Aluminium - Flexible.
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.
Related Information:
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.
Related Information:
Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated - Standard.
Related Information:
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at
Shafting - Aluminium - Ceramic Coated - Tapped.
Related Information:
Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.
Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting.
Related Information:
Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.
Related Information:
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Titanium shafting available in oversized and undersized tolerances
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.
Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.
Related Information:
For use with rail supports and open linear bearings
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at
Shafts - Idler.
Related Information:
This category may be available in the new MBA online store at
Shafts - Pinion.
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at
Rod - Drill Blanks.
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - Without Shaft.
Related Information:
One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.
Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at
Rail Supports - With Shaft - One Piece.
Related Information:
Includes linear shafting.
Related Information:
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at
Supports - Pedestal Two Bolt.
Related Information:
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - A-2 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - O-1 Oil Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - S-7 Air Hardening.
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at
Rod - Drill - Silversteel - W-1 Water Hardening.
Related Information:
Related Information:
Related Information:
Includes 303 and 304 Grade Stainless
Related Information:
Related Information:
Related Information:
Self Locking - Quick Release.
Related Information:
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. This category may be available in the new MBA online store at
Collars - Shaft - Gripfast - ABS Plastic.
Related Information:
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Precision machined. Convenient easy-to-assemble design. Steel 12L14 (9SMn Pb36)
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Standard one piece aluminium shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Aluminium.
Related Information:
Standard one piece nylon shaft collar with set screw
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Nylon.
Related Information:
Includes miniature precision types. 303 and 316 Types.
Related Information:
Includes miniature precision types. Carbon steel.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at
Collars - Shaft - Standard - Steel.
Related Information:
Miniature and large shaft extenders and reducers. Used to increase or reduce the diameter, or increase the length of shafts.
Also known as shaft increasers or shaft reducers. This category may be available in the new MBA online store at
Extenders - Shaft.
Related Information:
Used on conveyors, belt idlers, shock cushioners, stamping die part guides, supports etc.
Designed for use in machines and assembly operations where part movement and protection is needed. Durasoft rollers have a gentle but firm touch. Unique shape of holes adds to their soft but resilient nature. This category may be available in the new MBA online store at
Rollers - Durasoft - Shaft Mount - Black Neoprene.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153543
products in 2089 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.