Stays
15kg load capacity. Holds lid in fully opened position. Lift up to release.
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
Balls Metallic
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC.
Related Information:
Collars
Self Locking - Quick Release.
304 Stainless Body, Retention Ring, Balls and Springs.
Related Information:
Catches
304 Stainless Steel and Polyurethane
Screws Button Head
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
Related Information:
Screws Cheese Head
UNC Only
Nuts sold seperately - See Nuts.
Related Information:
Metric - UNC - UNF
Nuts sold seperately - See Nuts. DIN 84.
Related Information:
Screws Countersunk
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642.
Related Information:
Screws Hex Head
Metric - UNF - UNC
Nuts sold seperately - See Nuts.
Related Information:
Screws Round Head
Metric Only
Nuts sold seperately - See Nuts.
Related Information:
Mounts Leveling
ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.
Related Information:
Rod Ends Stainless Steel
Also known as Heim Joints
Dimensions not shown are available on request.
Pins Clevis
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
Related Information:
Screws Cap Head
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
Related Information:
Screws Countersunk
Flat Head Countersunk. Metric only.
Nuts sold seperately - See Nuts.
Related Information:
Flat Head Countersunk. Metric only.
Nuts sold seperately - See Nuts.
Related Information:
Washers Flat Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
Related Information:
Washers Square
Allthread
UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.
Nuts Lock
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
Screws Grub
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
Related Information:
Screws Self Tapping
Countersunk screws length includes head. ie, the full overall length of the screw.
Nuts Wing
304 and 316 Stainless Wing Nuts - A Pattern B18.17
Related Information:
Screws Grub
Standard grub screws. UNC - UNF - BA - METRIC.
Related Information:
Screws Self Tapping
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
Pulleys Timing GT2 2mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Cable
304 Stainless Steel
Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1.
Pins Wirelock
Also known as snapper pins
Related Information:
Also known as snapper pins
Related Information:
Washers Lock
304 Grade Stainless Steel
Washers designed to be used to help prevent nuts from vibrating loose.
Pins Roll
304 grade DIN1481.
Also known as sel-lok and bissell pins.
Related Information:
Eyebolts
304 Stainless Steel
Should not be used for angular lifts greater than 45o. Safety swivel hoist rings are recommended for such applications.
Keys and Keysteel
303, 304 and 316 key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
303, 304 and 316 grade key steel
Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.
Related Information:
Mounts Leveling
ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
Related Information:
ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
Related Information:
Eyebolts
Not recommended for lifting. 304 stainless steel.
Complete with nut. Rolled threads.
Linear Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Mounts Leveling
ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.
Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o swivel.
Related Information:
ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications. Adjusters.
Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 1o swivel.
Related Information:
Linear Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Catches
Draw pull catches are available in either steel or 304 stainless. Strike is included.
Linear Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127031
products in 2352 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.