Small Parts & Bearings - an MBA company

ES76 REID


Cross Referenced Part Numbers



ES-1270-2794-16-M Reid part number ES-76





OD (D0): 12.70. Overall Length (L0): 279.4. Wire Diameter (d): 1.60.

Retail Price: 0.00     
Lower price for quantities     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Belts Timing H Pitch 12.7mm


Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.

Related Information:


Pulleys Timing H Pitch 12.7mm


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


You may also be interested in

Sleeves


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.



Sleeves - Square Hole - Plain - Carbon Steel
Sleeves - Square Hole - Plain - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.



Sleeves - Square Hole - Threaded - Carbon Steel
Sleeves - Square Hole - Threaded - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.



Oil Seals


Oil Seals - Fluoroelastomer Rubber
Oil Seals - Fluoroelastomer Rubber

Also see combined categories:
All Oil Seals

DIN 3760 - High Temperature and chemical resistance.

Operating Temp. Range: -20oC to +240oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.


Dental Handpiece Parts


Intra 24CN - 24LN - 553 5761 Kavo Parts
Intra 24CN - 24LN - 553 5761 Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Sleeves


Sleeves - Hex Hole - Hardened
Sleeves - Hex Hole - Hardened

Also see combined categories:
All Hex Hole Sleeves

Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.



Sleeves - Square Hole - Plain - Hardened
Sleeves - Square Hole - Plain - Hardened

Also see combined categories:
All Square Hole Sleeves

Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.



Oil Seals


Oil Seals - Nitrile Rubber
Oil Seals - Nitrile Rubber

Also see combined categories:
All Oil Seals

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifically required please let us know when ordering.

Operating Temp. Range: -30oC to +90oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.


Prestige Bien Air Parts
Prestige Bien Air Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Bushes - Aluminium Bronze - Flanged
Bushes - Aluminium Bronze - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Related Information:


Bushes - Aluminium Bronze - Graphite Plug - Flanged
Bushes - Aluminium Bronze - Graphite Plug - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Related Information:


Bushes - Aluminium Bronze - Graphite Plug - Unflanged
Bushes - Aluminium Bronze - Graphite Plug - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Related Information:


Bushes - Aluminium Bronze - Unflanged
Bushes - Aluminium Bronze - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Used for dies, moulds and heavy machinery. C95400 Aluminium bronze.

ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.

Related Information:


Bushes - Bronze - Sintered - Flanged
Bushes - Bronze - Sintered - Flanged

Also see combined categories:
All Bronze Bushes
All Flanged Bronze Bushes

Oil impregnated flanged sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM.

Related Information:


Bushes - Bronze - Sintered - Unflanged
Bushes - Bronze - Sintered - Unflanged

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Oil impregnated sintered bronze bushes.

Precision items show an allowable Load Speed Rating in Newtons times RPM.

Related Information:


Bushes - Bronze - Solid
Bushes - Bronze - Solid

Also see combined categories:
All Bronze Bushes
All Unflanged Bronze Bushes

Solid precision leaded gunmetal bronze bushes. Either LG2 (C83600A) or C93200 as indicated in the listings.

Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.

Related Information:


Bushes - Bronze - Spherical - Sintered
Bushes - Bronze - Spherical - Sintered

Also see combined categories:
All Bronze Bushes

Spherical OD Oil Impregnated Sintered Bronze Bushes.

ID and OD oversized. Enquire if details required.

Related Information:


Bushes - Plastic - Clip - Bevelled Edge
Bushes - Plastic - Clip - Bevelled Edge

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.

Related Information:


Bushes - Plastic - Clip - Double Flanged
Bushes - Plastic - Clip - Double Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For use with sheet metal. Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F).

Related Information:


Bushes - Plastic - Ertalyte TX - Unflanged
Bushes - Plastic - Ertalyte TX - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Self lubricated, high mechanical strength, stiffness and hardness.


Related Information:


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Flanged
Bushes - Plastic - Iglidur A290 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Flanged
Bushes - Plastic - Iglidur X - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Rulon J - Flanged
Bushes - Plastic - Rulon J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Bushes - Plastic - Rulon J - Unflanged
Bushes - Plastic - Rulon J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Bushes - Stainless Steel and PTFE - Flanged
Bushes - Stainless Steel and PTFE - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.

Related Information:





Main Pages

About Us Balls List Bearings List Brands Catalogue Contact Us Charity Dental Bearings Dowel Pins Downloadable PDF Catalogue Ball Lock Pins Downloadable PDF Catalogue Balls Downloadable PDF Catalogue Ceramic Bearings Downloadable PDF Catalogue Circlips Downloadable PDF Catalogue Clevis Pins Downloadable PDF Catalogue Corrosion Resistant Bearings Downloadable PDF Catalogue Disc Springs Downloadable PDF Catalogue Dowel Pins Downloadable PDF Catalogue Economy Bearings Downloadable PDF Catalogue Hammer Drive Pins Downloadable PDF Catalogue High Speed Bearings Downloadable PDF Catalogue Key Steel Downloadable PDF Catalogue Knobs Downloadable PDF Catalogue Leveling Mounts Downloadable PDF Catalogue Metallic Bushes Downloadable PDF Catalogue O-Rings Downloadable PDF Catalogue Pins Downloadable PDF Catalogue Plastic Bearings Downloadable PDF Catalogue Polyvee Belts and Pulleys Downloadable PDF Catalogue Precision Shim Washers Downloadable PDF Catalogue Push On and Push In Rings Downloadable PDF Catalogue Rod & Tube Downloadable PDF Catalogue Roll Pins Downloadable PDF Catalogue Shaft Collars Downloadable PDF Catalogue Shim Sheet Downloadable PDF Catalogue Shoulder Screws Downloadable PDF Catalogue Sintered Bronze Bushes Downloadable PDF Catalogue Snap Rings Downloadable PDF Catalogue Socket Set Screws Downloadable PDF Catalogue Solid Bronze Bushes Downloadable PDF Catalogue Spring Steel Strip Downloadable PDF Catalogue Springs Downloadable PDF Catalogue Standard Ball Bearing Range Downloadable PDF Catalogue Super Precision Bearings Downloadable PDF Catalogue Taper Pins Downloadable PDF Catalogue Thrust Bearings Downloadable PDF Catalogue Thumb Screws and Nuts Downloadable PDF Catalogue Timing Belts Downloadable PDF Catalogue Timing Pulley Stock Downloadable PDF Catalogue Timing Pulleys Downloadable PDF Catalogue Vibration Mounts Downloadable PDF Catalogue Washers Downloadable PDF Catalogue Wave Washers Downloadable PDF Cross Reference ADR and SKF Downloadable PDF Cross Reference Anderton Circlips Downloadable PDF Cross Reference Barden Bearings Downloadable PDF Cross Reference Essentra Downloadable PDF Cross Reference Flocast Downloadable PDF Cross Reference K&S Metals Downloadable PDF Cross Reference McMaster Carr Downloadable PDF Cross Reference Miniature Precison Bearings Downloadable PDF Cross Reference Nordex Downloadable PDF Cross Reference NSK and NTN Downloadable PDF Cross Reference Ondrives Downloadable PDF Cross Reference Reid Supply Downloadable PDF Cross Reference SDP-SI Designatronics Downloadable PDF Cross Reference Seeger Circlips Downloadable PDF Cross Reference Sintered Bronze Downloadable PDF Cross Reference Small Parts Inc Downloadable PDF Cross Reference Timing Belts and Pulleys Freight Rates and Shipping Times Frequently Asked Questions Google Search Hobby Clearance Hobby Information Large Bearings Mailorder Form Order History Ordering Payment and Shipping Privacy Product Showcase Shipping Rates and Times Technical Terms


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131167 products in 2163 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131167 products in 2163 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.