Small Parts & Bearings - an MBA company

Searched For: ES70 REID


Cross Referenced Part Numbers



ES-0953-2794-12-M Reid part number ES-70





OD (D0): 9.53. Overall Length (L0): 279.4. Wire Diameter (d): 1.19.

Retail Price: 0.00 (Each )     
Lower price for quantities     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Dental Handpiece Parts


60 and 70 Borden Parts
60 and 70 Borden Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Washers Flat Rubber


Washers - Flat - Rubber
Washers - Flat - Rubber

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Nitrile Duro 70

This category may be available in the new MBA online store at Washers - Flat - Rubber.

Related Information:


Washers Flat Fibre


Washers - Flat - Fibre
Washers - Flat - Fibre

Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic

Flat red vulcanised fibre washers. Black available on request and sufficient quantity.

Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.

Related Information:


You may also be interested in

O-Rings


O-Rings - Silicone Rubber
O-Rings - Silicone Rubber

Also see combined categories:
All O-Rings

High thermal resistance and cold flexibility. Some dental applications are included in the listings. Commonly used in food appliactions.

Temperature Range: -70oC to +200oC. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.

Related Information:


Knobs Round


Knobs - Round - Male - Soft
Knobs - Round - Male - Soft

Also see combined categories:
All Round Knobs
All Knobs

Special high impact strength black technopolymer coated with soft touch elastomer chemically bonded (hardness 70 Shore A). Black matte finish. Resistant to solvents, oils, greases and other chemical agents. Zinc plated threaded steel stud. This category may be available in the new MBA online store at Knobs - Round - Male - Soft.

Related Information:


Dental Handpiece Parts


Top Air - Top LITE 700 and 800 Series Incl 898 W.H. Parts
Top Air - Top LITE 700 and 800 Series Incl 898 W.H. Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Flanges - Timing Pulley - Suit 12.700mm H Series - Aluminium
Flanges - Timing Pulley - Suit 12.700mm H Series - Aluminium

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys

This category may be available in the new MBA online store at Flanges - Timing Pulley - Suit 12.700mm H Series - Aluminium.

Related Information:


Flanges - Timing Pulley - Suit 12.700mm H Series - Carbon Steel
Flanges - Timing Pulley - Suit 12.700mm H Series - Carbon Steel

Also see combined categories:
All Timing Pulley Flanges

Use with timing pulley stock to custom make your own pulleys

This category may be available in the new MBA online store at Flanges - Timing Pulley - Suit 12.700mm H Series - Carbon Steel.

Related Information:


Socket Set Screws - Urethane Tipped - Stainless Steel
Socket Set Screws - Urethane Tipped - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Shore 70A Black Urethane tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Urethane Tipped - Stainless Steel.

Related Information:


7000 Abu Garcia Parts
7000 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


7000-C3 Abu Garcia Parts
7000-C3 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


7000C Abu Garcia Parts
7000C Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Belts - Timing - 12.700mm Pitch - H - 19.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 19.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 19.1mm Wide.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide
Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 25.4mm Wide.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 38.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 38.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 38.1mm Wide.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 50.8mm Wide
Belts - Timing - 12.700mm Pitch - H - 50.8mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 50.8mm Wide.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide
Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 76.1mm Wide.

Related Information:


Belts - Timing - 12.700mm Pitch - H - 9.5mm Wide
Belts - Timing - 12.700mm Pitch - H -  9.5mm Wide

Also see combined categories:
All H 12.7mm Pitch Timing Belts

Standard Series Timing Belts 12.700mm or 0.500 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. This category may be available in the new MBA online store at Belts - Timing - 12.700mm Pitch - H - 9.5mm Wide.

Related Information:


Gearmotors - DC PM - Size 70x114
Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.


AT70B Silstar Parts
AT70B Silstar Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


LS570 Mitchell Parts
LS570 Mitchell Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


9072702 Long Arm Jentschman Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Circlips - External - Grooveless
Circlips - External - Grooveless

Also see combined categories:
All External Circlips

Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).

Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. This category may be available in the new MBA online store at Circlips - External - Grooveless.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Taperlock bush required for bore.

Cast Iron and Steel. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 38.1mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 50.8mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Taperlock.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit H Series 12.700mm Pitch Timing Belts. Belt width 76.2mm. Taperlock bush required for bore.

Steel and Cast Iron. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Taperlock.

Related Information:


Balls - Chrome Steel
Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833. This category may be available in the new MBA online store at Balls - Chrome Steel.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore.

Related Information:


5230 1970 Models Abu Garcia Parts
5230 1970 Models Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Socket Set Screws - Urethane Tipped - Alloy Steel
Socket Set Screws - Urethane Tipped - Alloy Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Shore 70A Black Urethane tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.

This category may be available in the new MBA online store at Socket Set Screws - Urethane Tipped - Alloy Steel.

Related Information:


Belts - Timing - 14.000mm Pitch - HTD - 170mm Wide
Belts - Timing - 14.000mm Pitch - HTD - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Pitch (P) - 14.000mm.

Related Information:


Wire Rings - Internal - Round Section
Wire Rings - Internal - Round Section

Also see combined categories:
All Internal Circlips

Includes DIN7993B / RB / M1700 / BN826. Retaining rings. Snap Rings (USA). Round section circlips.

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins. This category may be available in the new MBA online store at Wire Rings - Internal - Round Section.

Related Information:


Belts - Timing - 14.000mm Pitch - GT - 170mm Wide
Belts - Timing - 14.000mm Pitch - GT - 170mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - STOCK - Aluminium
Pulleys - Timing - 12.700mm Pitch - H - STOCK - Aluminium

Also see combined categories:
All H 12.7mm Pitch Timing Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.

This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - STOCK - Aluminium.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - STOCK - Carbon Steel
Pulleys - Timing - 12.700mm Pitch - H - STOCK - Carbon Steel

Also see combined categories:
All H 12.7mm Pitch Timing Pulley Stock

For manufacture of timing pulleys or applications requiring multiple belts from a single drive.

This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - STOCK - Carbon Steel.

Related Information:


Pulleys - Timing - 14.000mm Pitch - GT - 170mm Wide - Taperlock
Pulleys - Timing - 14.000mm Pitch - GT - 170mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 170mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing - 14.000mm Pitch - GT - 170mm Wide - Taperlock.

Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Prestige Bien Air Parts
Prestige Bien Air Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 144275 products in 2044 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.