Small Parts & Bearings - an MBA company

EPL65 ANDERTON


Category Matches

Belts Rounthane


Belts - Rounthane
Belts - Rounthane


Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).

Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot) of length. Orders for more than one length of 305mm will be supplied as a continuous length. FDA / USDA approved.

Related Information:


Mounts Cylindrical


Mounts - Buffer - Special Purpose
Mounts - Buffer - Special Purpose

Also see combined categories:
All Cylindrical Mounts

Vibration dampening

Natural rubber with bonded in studs. 50 Durometer hardness. Use up to 65 Degrees C (150 Deg F).

Related Information:


Gearheads Inline


Gearheads - Inline - Planetary - Size 17 - Precision
Gearheads - Inline - Planetary - Size  17 - Precision

Also see combined categories:
All Inline Planetary Gearheads

Use with NEMA Size 17 Motors.

Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).

Related Information:


Shafting General Purpose


Rod - Drill - A-2 Air Hardening
Rod - Drill - A-2 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements.


650A FG Kavo Parts
650A FG Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


650B PB - 650C PB Kavo Parts
650B PB - 650C PB Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


6500 Abu Garcia Parts
6500 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


6500C - 6500C3 Abu Garcia Parts
6500C - 6500C3 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Ultima 650L BA Parts
Ultima 650L BA Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Washers - Spring - Wave Type - Carbon Steel
Washers - Spring - Wave Type - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.



Baitrunner 4500 - 6500A Shimano Parts
Baitrunner 4500 - 6500A Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


465LRN Coupling Kavo Parts
465LRN Coupling Kavo Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


266-650NT Adler Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Balls - Checking - Tungsten Carbide
Balls - Checking - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Balls - Fixture - Tungsten Carbide
Balls - Fixture - Tungsten Carbide

Also see combined categories:
All Fixture and Checking Balls

RC 65-68

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.

Related Information:


Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprocket Plates - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Push On Retaining Rings - Carbon Steel
Push On Retaining Rings - Carbon Steel

Also see combined categories:
All Push On Rings

M1465 / DTX / Seeger ZA and KS.

Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.


Collars - Shaft - Gripfast - ABS Plastic
Collars - Shaft - Gripfast - ABS Plastic

Also see combined categories:
All Round Bore Shaft Collars

Self Locking - Quick Release.

265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.

Related Information:


Dental Replacement Parts
Dental Replacement Parts


A list of additional parts available for handpieces and couplers including KaVo and W&H

This category contains miscellaneous dental parts excluding tools, bearings, turbines and o-rings. Parts for specific handpiece models can be found under the brand name on the internet store main index.

Related Information:


Latches - 200 Series - Heavy Duty
Latches - 200 Series - Heavy Duty


Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.


Wheels - Conveyor - Skate
Wheels - Conveyor - Skate

Also see combined categories:
All Wheels

Replacement acetal wheels with glass balls for product moving gravity feed skate conveyors. Plastic skate wheels are ideal for washdown or outdoor applications.

General Duty. Plain Centre.

Related Information:


Inserts - Thread Repair - Helicoil
Inserts - Thread Repair - Helicoil

Also see combined categories:
All Helicoil Inserts and Kits

Replacement helicoil inserts for after you have purchased a starter kit or tools separately.

Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.


Bearings - Tapered Roller - Cone
Bearings - Tapered Roller - Cone


Replacements for existing tapered roller cones (inner part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.



Bearings - Tapered Roller - Cup
Bearings - Tapered Roller - Cup


Replacements for existing tapered roller cups (outer part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.



Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Accessories - Hobby - Wheel Nuts Adaptors and Pins
Accessories - Hobby - Wheel Nuts Adaptors and Pins


Replacement Wheel Nuts, adaptors and pins for remote control cars



Tools - Sets - Foldup
Tools - Sets - Foldup

Also see combined categories:
All Tools

Handy sets of popular sized hex and torx wrenches.

Highest quality 8650 chrome nickel alloy heat treated and finished to resist rust. Ergo style has colour coded handles. Classic style has one piece steel grip handle. Conveniently folds up like a jack knife when not in use.


Pins - Hammer Drive - Round Head - Stainless Steel
Pins - Hammer Drive - Round Head - Stainless Steel

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Latches - 1-4 Turn -Tee Handle - Non Locking
Latches - 1-4 Turn -Tee Handle - Non Locking

Also see combined categories:
All Quarter Turn Latches

Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.

Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Keysteel Lengths - Rectangular - Carbon Steel
Keysteel Lengths - Rectangular - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.

Related Information:


Keysteel Lengths - Square - Carbon Steel
Keysteel Lengths - Square - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.

Related Information:


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Keysteel Lengths - Rectangular - Stainless Steel
Keysteel Lengths - Rectangular - Stainless Steel

Also see combined categories:
All Keysteel Lengths

303, 304 and 316 key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.

Related Information:


Keysteel Lengths - Rectangular - Zinc Plated
Keysteel Lengths - Rectangular - Zinc Plated

Also see combined categories:
All Keysteel Lengths

Zinc plated carbon steel key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. Zinc plating may be silver or yellow in colour.

Related Information:


Keysteel Lengths - Square - Zinc Plated
Keysteel Lengths - Square - Zinc Plated

Also see combined categories:
All Keysteel Lengths

Zinc plated carbon steel key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. Zinc plating may be silver or yellow in colour.

Related Information:


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x 75.0 x 44.0mm
Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x  75.0 x 44.0mm

Also see combined categories:
All Right Angle Gearboxes

BLH40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Related Information:


Keysteel Lengths - Square - Stainless Steel
Keysteel Lengths - Square - Stainless Steel

Also see combined categories:
All Keysteel Lengths

303, 304 and 316 grade key steel

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled.

Related Information:


Bearings - Ball - 4 Point Contact
Bearings - Ball - 4 Point Contact


4 Point Contact Bearings support Axial Loads in both directions. Can replace double row angular contact bearings where space is limited.

Related Information:


Inserts - Expansion - Press In - 303 Stainless - Flanged
Inserts - Expansion - Press In - 303 Stainless - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Inserts - Expansion - Press In - 303 Stainless Steel
Inserts - Expansion - Press In - 303 Stainless Steel

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127031 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 127031 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.