Gears Inch Bevel
For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.
20
o Pressure Angle. Do not mix gears from different sets. See
Gears - Mitre for 1:1 ratios.
Related Information:
Pinion Wire Imperial
Brass and carbon steel.
Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.
Gears Inch Spur
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.
PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.
PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth.
You may also be interested in
Latches Draw
Passivated stainless steel. Latches mount with M4 screws, No. 8 screws or 5/32 rivets. Type B keeper uses a countersunk screw.
Keepers included. Type SC-97533 has a hole for a padlock.
Gears Inch Racks
14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.
20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.
Universal Joint Covers
For Single and Double Universal Joints.
-27 oC to 70 Deg C temp range (constant). -32 oC to 120 Deg C temp range (intermittent).
Related Information:
Thread Inserts
Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Gears Inch Spur
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. 303 Stainless Steel. DP stands for Diametrical Pitch and is an imperial measurement system.
32 Diametrical Pitch. Approx 2.49mm between teeth.
Related Information:
Thread Inserts
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
14.5o Pressure Angle - 4.08o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
Worms and Gears must be chosen from the same pitch and series to match. DP is Diametrical Pitch.
20o Pressure Angle - 8.13o Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
Related Information:
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
T Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Timing pulleys to suit T10 Series belts
Aluminium Alloy. Finished through bore ready to assemble.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 19.1mm (3/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 3.18mm (1/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 4.76mm (3/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 7.93mm (5/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 9.53mm (3/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
PowerGrip(R) TruMotion(R) Timing Belts in 2.032mm or 0.080 inch pitch.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oC to +90oC, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. TruMotion(R) belts have a durable wear surface for longer life and are RoHS compliant. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. RoHs compliant.
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 3.0 to 3.2mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial. Socket Cap Screw is Supplied with Pulley. Aluminium Alloy.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With brass insert.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. No locking device.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 9.5 to 9.6mm wide
2.032mm metric is equivalent to 0.080 pitch imperial. Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Use with timing pulley stock to custom make your own pulleys
Related Information:
Levelling adjusters. Max load 3200kg.
Used for shallow drawers, tool chests and medical carts.
Rail mounting. Hold in detent. Full extension. 13.5mm Side space. Includes 32mm hole pattern as well as traditional hole pattern.
Used for shallow drawers, tool chests and medical carts.
Hold in detent. Full extension. 12.7mm Side Space. Includes 32mm hole pattern as well as traditional hole pattern.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131170
products in 2164 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.