Small Parts & Bearings - an MBA company

EP26 ONDRIVES


Cross Referenced Part Numbers



PSP-020-006-S2 Ondrives part number EP2-6



Nom. Hole Diameter: 2.00. Length: 6.00. Drill Size: 1.99 - 2.10.

Online Price: 0.00     
Stock: Pre-Order (due 8 weeks)     
Due dates are estimates only     


Category Matches

Gearbox Parts


P30-60 Ondrives Parts
P30-60 Ondrives Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


RC Spare Parts - Losi
RC Spare Parts - Losi


Losi spare parts listed by description. Eight - 8IGHT -, Micro desert truck, Mini desert truck, Mirco-T, LST 2 and XXL, Night and Comp Crawler, 1/10 Onroad and Offroad, XXX4, XXXT, 1/8 Scale, Micro Vehicles, AFT, MGB, Big Shot Buggy, Monster Truck

Also incldes Desert Truck, Fury Truck, Grappler Rock Crawler, JR-X, Race Roller, MGB, Mach 15, Mach 26, Micro and Mega Baja, 1/36 Scale. MINI-T, Mini Slider, Road Weapon, Short Course, Speed-T.


266-650NT Adler Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Motors - DC 26.9X23.8 mm
Motors - DC 26.9X23.8 mm

Also see combined categories:
All DC Motors

M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


Motors - DC 26.9X24.2X18.3 mm
Motors - DC 26.9X24.2X18.3 mm

Also see combined categories:
All DC Motors

MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM. Standard 130 Size Hobby Motor.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:


RC Spare Parts - Colt
RC Spare Parts - Colt


Colt spare parts listed by description. Includes 1/10 Belt Drive, Colt Buggy, GP, EVO7, Nissan Silvia, 2WD, 4WD, Toyota IS200, Monster Truck, EP Touring Car, MT Truggy, Mini Cooper, Shaft Drive

Refer to your parts manual to ensure you purchase the correct items.


Pulleys - Timing - 10.000mm Pitch - T10 - 26mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - T10 - 26mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit T10 Series belts

Aluminium Alloy. Finished through bore ready to assemble.

Related Information:


Collars - Shaft - Gripfast - ABS Plastic
Collars - Shaft - Gripfast - ABS Plastic

Also see combined categories:
All Round Bore Shaft Collars

Self Locking - Quick Release.

265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.

Related Information:


Sprockets - Ladder Chain - 7.264mm Pitch - Size 18
Sprockets - Ladder Chain - 7.264mm Pitch - Size 18

Also see combined categories:
All Sprockets for Ladder Chain

Plastic, bronze and steel.


Related Information:


Latches - 200 Series - Heavy Duty
Latches - 200 Series - Heavy Duty


Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.


Circlips - External - Inverted
Circlips - External - Inverted

Also see combined categories:
All External Circlips

N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).

Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.

Related Information:


O-Rings - EPDM Rubber
O-Rings - EPDM Rubber

Also see combined categories:
All O-Rings

Suitable for heated water and steam.

Temperature Range: -55oC to +150oC. Chemically resistant to Hydraulic Fluids. Resistant to alcohols, glycol engine coolants and SKY-DROL (phosphate ester hydraulic fluid).

Related Information:


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Circlips - Internal - Round Section
Circlips - Internal - Round Section

Also see combined categories:
All Internal Circlips

Includes DIN7993B / RB / M1700 / BN826. Retaining rings. Snap Rings (USA).

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


Suction Cups
Suction Cups


EPDM or Natural Rubber as listed against each item

EPDM is a higher grade rubber that rates excellent for ozone resistance and is used for molded parts used outdoors. SBR is Styrene-butadiene Rubber is a general purpose rubber but not recommended for continual use outdoors or in oily environments.


Seals - Trim - Push On - EPDM with Steel Core
Seals - Trim - Push On - EPDM with Steel Core


Weatherstrip and trim by simply pushing over raw edges.



Pool Sweep Arneson Parts
Pool Sweep Arneson Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


RC Spare Parts - Hangar9
RC Spare Parts - Hangar9


Hangar Nine airplane parts listed by description. Parts to suit Alpha 40, Corsair, Cessna, Edge 540, Extra 260, Hellcat, Funtana, J3 Cub, P-40 Warhawk, P-47, P-51 Mustang, Piper Pawnee, Sopwith Camel, Spitfire, Sukhoi SU-26, T-34 Mentor

Includes control line, handle and attachments.


O-Rings - Cord
O-Rings - Cord


Nitrile, Fluoroelastomer and EPDM continuous length o-ring cord.

Nitrile: Temp Range: -30oC to +90oC / Fluoroelastomer: Temp Range -20oC to +240oC. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Nitrile: Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Fluoroelastomer (Viton(R)): Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.

Related Information:


Inserts - Thread Repair - EZ-Lok - Individual Kits
Inserts - Thread Repair - EZ-Lok - Individual Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:


Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel
Inserts - Thread Repair - EZ-Lok - Solid Carbon Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:


Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel
Inserts - Thread Repair - EZ-Lok - Solid Stainless Steel

Also see combined categories:
All EZ Lok inserts and Kits

Easy to install with a standard tap, bolt and wrench.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Simply drill and tap the hole to suit the external thread. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:


Inserts - Thread Repair - Helicoil
Inserts - Thread Repair - Helicoil

Also see combined categories:
All Helicoil Inserts and Kits

Replacement helicoil inserts for after you have purchased a starter kit or tools separately.

Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.


Inserts - Thread Repair - Helicoil Extracting Tools
Inserts - Thread Repair - Helicoil Extracting Tools


Extracting tools are used to remove helicoil inserts. This is done by applying the tool to the insert, striking the tools head and turning it counter-clockwide.



Inserts - Thread Repair - Helicoil Installation Tools
Inserts - Thread Repair - Helicoil Installation Tools


Tools for helicoil inserts include economy style and production style prewinder and threaded mandrel types



Inserts - Thread Repair - Helicoil Starter Sets
Inserts - Thread Repair - Helicoil Starter Sets

Also see combined categories:
All Helicoil Inserts and Kits

Helicoil sets include 3 lengths of 1x, 1.5x and 2x the thread diameter. Also included is a tap, an installation tool, a drill and a tang removal tool packed in a sturdy plastic case.

Stainless inserts. Full instructions included. Helicoil kits include a prewinder tool for fine threads or a threaded mandrel for course and metric threads. Metric and Imperial available.


Inserts - Thread Repair - Helicoil Tang Breakoff Tools
Inserts - Thread Repair - Helicoil Tang Breakoff Tools


The driving tangs of helicoil inserts must be removed to prevent interference with the end of the assembled screw. For inserts over 1/2 inch use long nosed pliers.



Inserts - Thread Repair - Keylocking
Inserts - Thread Repair - Keylocking

Also see combined categories:
All Keylocking Inserts and Kits

Steel or 303 Stainless Steel as indicated in the tables. Also known as keenserts.

Steel or 303 Stainless Steel as indicated in the tables. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.

Related Information:


Inserts - Thread Repair - Keylocking Assortment Kits
Inserts - Thread Repair - Keylocking Assortment Kits

Also see combined categories:
All Keylocking Inserts and Kits

Also known as keenserts.


Related Information:


Inserts - Thread Repair - Keylocking Insertion Tools
Inserts - Thread Repair - Keylocking Insertion Tools


Used to insert keylocking inserts - keensert style. Keylocking inserts can be wound in without these tools but the tools make the job much easier. Also known as keenserts.


Related Information:


Inserts - Thread Repair - Keylocking Starter Sets
Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.

Related Information:


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Inserts - Thread Repair - EZ-Lok - Selection Kits
Inserts - Thread Repair - EZ-Lok - Selection Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains a selection of E-Z Lok inserts

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:


Tools - Thread Repair
Tools - Thread Repair

Also see combined categories:
All Tools

Quickly repairs damaged screws

Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.


Cranks - Handwheel - Spoked
Cranks - Handwheel - Spoked

Also see combined categories:
All Spoked Handwheel Cranks

Pressed steel with RAL 9005 black epoxy resin coating. Hub: Welded with H9 tolerance plain hole (Type B) or through square H11 tolerance hole (Type V). Axial and radial runout lower than IT 12.


Tools - Mandrels and Nosepieces - For Klik Rivet Nuts
Tools - Mandrels and Nosepieces - For Klik Rivet Nuts

Also see combined categories:
All Tools

Required for Thread Setter Tool

Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.

Related Information:


Balls - Rubber - Santoprene 40D
Balls - Rubber - Santoprene 40D

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.

Related Information:


Balls - Rubber - Santoprene 87A
Balls - Rubber - Santoprene 87A

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.

Related Information:


Pins - Ball Lock - Flanged Receptacles
Pins - Ball Lock - Flanged Receptacles

Also see combined categories:
All Ball Lock Receptacles

Provide a permanent and proper mating hole for commercial and industrial type quick release ball lock pins. Also called detent pins.

Designed to be used on materials or in applications where the pin does not have anything to lock against. Positive lock detent pins. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.

Related Information:


Gears - Spur - 96DP - Aluminium
Gears - Spur -  96DP - Aluminium

Also see combined categories:
All 96DP Spur Gears
All Metal 96DP Spur Gears

PCD = No. of Teeth x 0.265mm (1/96 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - 96DP - Stainless
Gears - Spur -  96DP - Stainless

Also see combined categories:
All 96DP Spur Gears
All Metal 96DP Spur Gears

PCD = No. of Teeth x 0.265mm (1/96 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 96 Diametrical Pitch. Approx 0.83mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Wheels - Conveyor - Skate
Wheels - Conveyor - Skate

Also see combined categories:
All Wheels

Replacement acetal wheels with glass balls for product moving gravity feed skate conveyors. Plastic skate wheels are ideal for washdown or outdoor applications.

General Duty. Plain Centre.

Related Information:


Latches - Rotary Action - Link Lock - Keepers
Latches - Rotary Action - Link Lock - Keepers


Required for link lock rotary action latches. Match keeper with correct latch from selection.



Spiral Rings - External - Heavy Duty
Spiral Rings - External - Heavy Duty

Also see combined categories:
All External Spiral Rings

AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.

Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2.


Spiral Rings - External - Medium Duty
Spiral Rings - External - Medium Duty

Also see combined categories:
All External Spiral Rings

AE / WS / AS3218 / RS / MIL-R-27426A1 - Spring Steel and Stainless Steel.

Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AE, Smalley: WS, Spirolox and Ramsey: RS, Aerospace AS3218, MIL-R-27426A1.


Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems



Bearings - Tapered Roller - Cone
Bearings - Tapered Roller - Cone


Replacements for existing tapered roller cones (inner part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.



Bearings - Tapered Roller - Cup
Bearings - Tapered Roller - Cup


Replacements for existing tapered roller cups (outer part). Match with part number on your existing bearing. It is recommended that you change both cup and cone whenever possible.



Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126239 products in 2739 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126239 products in 2739 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.