Circlips
Basic imperial and metric e-clips DIN6799 and N1500. Stainless Steel PH15-7 Mo.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. This category may be available in the new MBA online store at
E-Clips - Basic - Stainless Steel.
Related Information:
You may also be interested in
Pins Clevis
Match with a suitable E-Clip or Circlip to suit groove size shown in listings
In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Grooved end to suit retaining clip instead of pin. This category may be available in the new MBA online store at
Pins - Clevis - Stainless Steel 300 Grade - Groove Locking.
Related Information:
Circlips
Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated. This category may be available in the new MBA online store at
E-Clips - Basic - Carbon Steel.
Related Information:
Eyebolts
316 Stainless Steel
Any deviations such as angular lifts, shock loads, modifications of the basic forging etc will result in drastically reduced maximum loads.
Clips
Also known as internal hitch pins, bridge pins or humpback pins
Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.
301 S11/S22 Stainless Steel. Used on the outside diameter of a bearing, shaft or similar equipment. This category may be available in the new MBA online store at
Snap Rings - External - Stainless Steel.
Cable
304 Stainless Steel
Clips
Rotor Clip TY. Stainless Steel hardness HR15N 82.5-86
Eyebolts
316 Stainless Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
Related Information:
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips. This category may be available in the new MBA online store at
Circlips - External - Inverted.
Related Information:
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. This category may be available in the new MBA online store at
Pins - Clevis - Stainless Steel 316 - Pin Locking.
Related Information:
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
Related Information:
Also known as Heim Joints
Also known as Heim Joints
Dimensions not shown are available on request.
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 304 Grade.
Related Information:
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316 Grade.
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Stainless Steel - 316L Grade.
Related Information:
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel. This category may be available in the new MBA online store at
Balls - Stainless Steel - 400 Grade.
Related Information:
430 Grade stainless steel strip
Flat washers.
Related Information:
Flat washers.
Related Information:
Precision Tolerances.
Related Information:
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Includes K&S Metals range and more.
Related Information:
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Also known as Heim Joints
Also known as Heim Joints
316 stainless steel wire rings.
Stainless Steel. Lower profile than a dome nut.
Stainless Steel.
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at
Nuts - Hexagonal - Stainless Steel.
304 and 316 Stainless Wing Nuts - A Pattern B18.17
Related Information:
Split pins.
Hole size indicated is maximum for the pin to be effective. If the pin you require is not available, you may be able to use the next larger diameter so long as the pin is smaller than your hole size. Longer lengths may be cut back to a suitable length. This category may be available in the new MBA online store at
Pins - Split - Stainless Steel.
Related Information:
Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.
Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated. This category may be available in the new MBA online store at
Pins - Clik - Stainless Steel 316 Grade.
Related Information:
Spirol Pins. Coiled roll pin.
Related Information:
Spirol Pins. Coiled roll pin.
Related Information:
300 Grade Stainless DIN1481/ISO8752.
Related Information:
420 grade stainless DIN1481/ISO8752.
Related Information:
For countersunk screws.
Hollow round tubing for general hobby applications.
Includes K&S Metals range and more. May be slightly oversized on OD so some reworking might be required before fitting closely mating parts. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. This category may be available in the new MBA online store at
Tube - Round - Stainless Steel.
Related Information:
Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6885
Related Information:
An economical way to secure the ends of extension springs, and provide easy adjustment.
This category includes short and long lengths
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote. This category may be available in the new MBA online store at
Springs - Compression - Stainless Steel.
Related Information:
Drawbar springs have long steel loops that pass through the centre of the spring and hook around the opposite end, compressing the spring on loading.
This design helps prevent unexpected overloading and fracturing that can occur in standard extension springs by stopping and hold the load at the spring limit. The spring rate indicates the load required to pull out the first 25mm of the spring. This category may be available in the new MBA online store at
Springs - Drawbar - Stainless Steel.
Related Information:
Includes long lengths up to 1 metre
Zinc Plated Spring Steel not recommended for applications exceeding 121
oC (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260
oC (500 Deg F). 302 stainless steel is slightly magnetic. This category may be available in the new MBA online store at
Springs - Extension - Stainless Steel.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Checking - Stainless Steel.
Related Information:
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Checking - Stainless Steel - With Tapped Shank.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.