Dual Vee Bearings
Vee guide rails for vee grooved track roller guide wheels.
Related Information:
Vee guide rails for vee grooved track roller guide wheels.
Related Information:
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Rubber base meets FDA 177-2600. 5o swivel for good floor contact.
With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.
With drilled and counterbored holes for mounting. Urethane bonded to steel plate.
With drilled and counterbored holes for mounting. Neoprene only, no steel plate.
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. Includes rest position for plunger to stay in retracted position. This category may be available in the new MBA online store at
Plungers - Indexing - Locking - With Mounting Plate - Steel.
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum. This category may be available in the new MBA online store at
Springs - Constant Force.
Related Information:
Used to prevent change in locking position due to shearing force. Spring loaded for use in fastening, locating and indexing on equipment, tooling and other applications.
Spring loaded to work in a variety of applications on both tooling and equipment that require surface mounting. Plunger is hardened and ground. Knob is black matte plastic. Mounting plate is zinc plated steel. This category may be available in the new MBA online store at
Plungers - Indexing - Non Locking - With Mounting Plate - Steel.
Ideal for precision applications where mounting space is limited
Gothic arch grooves at raceway contacts enables slide to sustain loads & movement from any direction. Made from stainless steel or plastic for corrosion resistance. End caps have oil holes for easy relubrication. This category may be available in the new MBA online store at
Rail Systems - Miniature Profile.
Cable ties with screw mounting holes.
Adjustable supports for all kinds of machinery. Mounting feet levelers.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25o from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
Related Information:
20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.
Switchs are rated at 10amp @ 600VAC with finger safe screw terminals. This category may be available in the new MBA online store at
Switches - Rocker.
Used with cam action indexing plungers
Related Information:
Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Used for filing cabinets, utility and industrial truck storage, machine tool drawers, generators and heavy mechanical devices.
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
Permanent Magnet.
Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned. This category may be available in the new MBA online store at
Dual Vee - Adaptor Bushings.
Related Information:
Levelling adjusters. Steel and stainless steel socket internal threads. Use your own custom thread length.
Related Information:
Levelling adjusters. Steel and stainless steel threads.
Levelling adjusters. Steel and stainless steel threads.
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs and simplify designs. Designed to press into a mounting plate as thin as 1.5mm.
Clinches into a plate bored to the required housing bore. Minimum plate thickness 1.6mm to no maximum. Maximum mounting hardness 100 Rockwell B. Operating temperature Minus 34 oC to Plus 121 Deg C. Compensates for mounting hole tolerances up to 0.07mm. 4.76 to 10mm bores. RoHS, REACH and SVHC environmental compliant.
Mounting feet let you isolate all types of machinery and equipment from vibration and floor motion.
Mounting feet let you isolate all types of machinery and equipment from vibration and floor motion.
Spyraflo sintered bronze bearing in a special self-clinching steel housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
Spyraflo acetal bearings in a special steel self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information. +/- 5% Static Alignment. See animation link at bottom of web page. Panel material no harder than RB65/RB75. Panel hole to be punched or machined to size A (+0.07/-0.00mm).
Related Information:
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base. Use as mounting feet. This category may be available in the new MBA online store at
Adjusters - Rigid.
Related Information:
For mounting of linear shafting.
Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at
Rail Supports - Without Shaft.
Related Information:
Levelling adjusters. Reduces noise and vibration on heavy machinery, compressors and presses.
High strength aluminium alloy mounting plate is embedded in each pad with two tapped mounting holes for installation on all types of machines. The elastomer compound used in these pads is highly resistant to oil and chemicals. 1/2 UNC thread cold forged x 2.5 inch bolt supplied with each mount. Thousands of tiny suction pockets on the bottom prevent the machine from walking or slipping out of position. This category may be available in the new MBA online store at
Mounts - Leveling - Studded - Machine - Cushioned.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
With steel core and washer moulded inside. Counterbored hole to accept a socket head cap screw.
Levelling adjusters. ANSI 304 stainless steel provides high corrosion resistance. Rounded polished base for fluid run-off during washdown applications.
Operating temperature -20 to 100o C. Wrench flats in thread still allow for full use of threaded section. 12o articulating swivel. 2 bolt holes in base allows for anchoring.
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size. This category may be available in the new MBA online store at
Dual Vee - Guide Wheels.
Related Information:
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed. This category may be available in the new MBA online store at
Dual Vee - Guide Wheels - Studded.
Related Information:
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Compression shear mounts for harsh environments.
Excellent protection against shock vibration and noise4 in compression and shear applications. Developed especially for applications in harsh environments in food and pharmaceutical industries. High dampening characteristics. Stainless top plate is domed to guard against oil contamination. Low profile. Compact design. Elastomer insert is made from highly chemical resistant nitrile with good deflection properties. Concentric rings in the base of the insert firmly anchor machine to the floor.
Related Information:
Corrosion resistant designed with high grade nitrile rubber and stainless steel.
Related Information:
Designed with high grade nitrile rubber and zinc plated steel.
Swivel movement plus or minus 7
o for stable support on inclined floors. Nitrile rubber base helps ensure stability. This category may be available in the new MBA online store at
Mounts - Anti-Vibration - Zinc Plated Steel.
Related Information:
Tough bonded neoprene. Patented pivotal leveler keeps equipment level and dampens an average 85% of noise. Adjusters.
The mounting nut which holds the stud is molded into the pad in a steel bracket and rotates freely permitting at least 6.35mm of leveling. Includes stud epoxied into the base mount. This category may be available in the new MBA online store at
Mounts - Pivotal Levelers - With Stud.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.