Small Parts & Bearings - an MBA company

DRILL ROD


Category Matches

Shafting General Purpose


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.


Rod - Drill - General
Rod - Drill - General

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Chrome vanadium alloy with unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight. Heat treating by air, water or oil.

Related Information:


Rod - Drill - A-2 Air Hardening
Rod - Drill - A-2 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Rod - Drill - O-1 Oil Hardening
Rod - Drill - O-1 Oil Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Rod - Drill - Oil Hardening - 480 Series
Rod - Drill - Oil Hardening - 480 Series

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

General purpose tool steel with good wear resistance, toughness and machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Rod - Drill - S-7 Air Hardening
Rod - Drill - S-7 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Rod - Drill - W-1 Water Hardening
Rod - Drill - W-1 Water Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight.


Shafting - Unground - Silver Steel
Shafting - Unground - Silver Steel

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.

See also drill rod. Drill Rod.

Related Information:


You may also be interested in

Shafting Precision Ground


Shafting - Pre Drilled and Tapped - High Carbon Steel
Shafting - Pre Drilled and Tapped - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

For use with rail supports and open linear bearings

Straightness: 0.1 mm / mtr.


Shafting - Pre Drilled and Tapped - Stainless Steel Steel
Shafting - Pre Drilled and Tapped - Stainless Steel Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings



Dental Handpiece Parts


Drill 8-12000 RPM Bravo Bedetrice Parts
Drill 8-12000 RPM Bravo Bedetrice Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Fastening Bushings


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Tools Cutting


Tools - Drill Bits
Tools - Drill Bits

Also see combined categories:
All Tools

Micro miniature drill bits starting from 0.32mm up to larger standard sizes. Sutton - PN - Bordo.

Lengths shown are based on standard stock but may vary.


Tools - Drill Bits - Reduced Shank


Reduced Shanked Drill Bits



Tools General


Tools - Drills
Tools - Drills

Also see combined categories:
All Tools

Hobby drill for very small bits.



Screws Self Tapping


Screws - Self Drilling - Hex Head - With Washers
Screws - Self Drilling - Hex Head - With Washers

Also see combined categories:
All Self Drilling Screws

With bonded neoprene washer. Galvanised for corrosion resistance.



Screws - Self Drilling - Hex Washer Head
Screws - Self Drilling - Hex Washer Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.



Screws - Self Drilling - Pan Head
Screws - Self Drilling - Pan Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.



Shafting Precision Ground


Shafts - Idler
Shafts - Idler


Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.

Related Information:


Bumpers


Bumpers - Square and Rectangle
Bumpers - Square and Rectangle

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene only, no steel plate.



Bumpers - Square and Rectangle - Steel Plated - Neoprene
Bumpers - Square and Rectangle - Steel Plated - Neoprene

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.



Bumpers - Square and Rectangle - Steel Plated - Urethane
Bumpers - Square and Rectangle - Steel Plated - Urethane

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Urethane bonded to steel plate.



Ball Parallels


Parallels - Ball
Parallels - Ball


Used for handling large work in drill presses or band saw machines.

Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet.


Thread Inserts


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Tools Bits


Bits - Power
Bits - Power


Power bits for use with power screwdrivers and drills



Thread Inserts


Inserts - Expansion - Press In - 303 Stainless - Flanged
Inserts - Expansion - Press In - 303 Stainless - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Inserts - Expansion - Press In - 303 Stainless Steel
Inserts - Expansion - Press In - 303 Stainless Steel

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Tensioners


Tensioner - Vertical Mount
Tensioner - Vertical Mount

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner.

Related Information:


Thread Inserts


Inserts - Thread Repair - EZ-Lok - Individual Kits
Inserts - Thread Repair - EZ-Lok - Individual Kits

Also see combined categories:
All EZ Lok inserts and Kits

Contains 20 inserts per kit along with a standard tap, drill bit and installation tool. Installation tool is not needed but will make multiple installations easier.

Automatic self locking pressure activated adhesive on external thread. Prevent or repair stripped threads. No special tools required. Install with a bolt and wrench. Metric, UNC and UNF.

Related Information:


Tensioners


Tensioner - Heavy Duty - Type 2
Tensioner - Heavy Duty - Type 2

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90o and is anchored by set screws.

Related Information:


Tensioner - Heavy Duty - Type 3
Tensioner - Heavy Duty - Type 3

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Shaft is located in the centre of the tensioner between the adjusting slots.

Related Information:


Tensioner - Heavy Duty - Type 4
Tensioner - Heavy Duty - Type 4

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 38.1mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 50.8mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 76.2mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Steel and Cast Iron. No grub screw. Hub requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pins - Groove
Pins - Groove

Also see combined categories:
All Groove Pins

Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.

An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole.

Related Information:


Pulleys - Timing - 8.000mm Pitch - GT2 - 50mm Wide - Through Bore
Pulleys - Timing -  8.000mm Pitch - GT2 - 50mm Wide  - Through Bore

Also see combined categories:
All 8mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit HTD 8.000mm Pitch Timing Belts. Suits belts 50mm wide.

Black oxide coated steel. No locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - T5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - T5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts. Suits belts 9.5 to 10.0mm wide.

Aluminium alloy. No locking provided. You will need to drill and tap the hub to suit your desired grub screw. Tapped hubs can be provided on request.

Related Information:


Pulleys - Timing - 5.000mm Pitch - T5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - T5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts. Suits belts 15.0 to 16.0mm wide.

Aluminium alloy. No locking provided. You will need to drill and tap the hub to suit your desired grub screw. Tapped hubs can be provided on request.

Related Information:


Pulleys - Timing - 5.000mm Pitch - T5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - T5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts. Suits belts 25.0mm to 25.4mm wide.

Aluminium alloy. No locking provided. You will need to drill and tap the hub to suit your desired grub screw. Tapped hubs can be provided on request.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124352 products in 2772 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.