Small Parts & Bearings - an MBA company

DARS000DA REID


Cross Referenced Part Numbers



BLP-048-0127-DR-S17 Reid part number DARS-000DA





Nominal Diameter: 4.76. Grip Length: 12.70. Pin Material Grade: 17-4 PH Stainless.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Motors DC


Motors - DC 20.0X25.0 mm
Motors - DC 20.0X25.0 mm

Also see combined categories:
All DC Motors

1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts


Related Information:


Studs


Studs - Threaded - Driver
Studs - Threaded - Driver


Medium carbon steel with black oxide finish. 125,000 PSI minimum tensile strength. With wrench flats in the centre.



Studs - Threaded - Standard
Studs - Threaded - Standard


Metric and imperial sizes. Steel and 303 stainless steel.

Yield strength 100,000 PSI. Tensile strength 125,000 PSI.


You may also be interested in

Spring Motors


Spring Motor Assemblies - Open - RINO
Spring Motor Assemblies - Open - RINO

Also see combined categories:
All Spring Motors

Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.

Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.


Thread Inserts


Inserts - Thread Repair - Helicoil
Inserts - Thread Repair - Helicoil

Also see combined categories:
All Helicoil Inserts and Kits

Replacement helicoil inserts for after you have purchased a starter kit or tools separately.

Stainless 18-8 inserts with a hardness of RC43-50 and tensile strength above 200,000 PSI. Metric and Imperial available. Screw locking inserts have a series of straight segments to provide self-locking torque on the bolt, eliminating a need for other threadlocking methods.


Inserts - Thread Repair - Recoil
Inserts - Thread Repair - Recoil

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. Replacement inserts for your kit.

Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.


Linear Bearings


Bearings - Linear - Sliding - Ceramic Coated
Bearings - Linear - Sliding - Ceramic Coated

Also see combined categories:
All Sliding Linear Bearings

Approved for direct food contact in applications where animal fat or food approved lubricants are present.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Minimum shaft hardness RC35. Max PV 40,000. Temperature range -125 oC to +226 Deg C. Max static PSI 5000.


Linear Slides


Slides - Dovetail
Slides - Dovetail

Also see combined categories:
All Linear Slides

Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.

Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.


Couplings Helical and Slit


Couplings - Reli-a-flex - Long Series - Clamp Type
Couplings - Reli-a-flex - Long Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Couplings - Reli-a-flex - Short Series - Clamp Type
Couplings - Reli-a-flex - Short Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Housings with Bearing


Housings - Bearing - Pedestal - Miniature - Self Aligning
Housings - Bearing - Pedestal - Miniature - Self Aligning

Also see combined categories:
All Housings with Integral Bearing

Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs. Simplify designs.

Small and cost effective. All bore sizes are mounted in the same size housing for ease of design and cost efficiency. High precision bearings pre-mounted with a 5o misalignment capability. 40,000 RPM recommended maximum speed with testing. 27kgf radial static capacity, 54kgf radial dynamic capacity per bearing. RoHS, REACH and SVHC environmental compliant.


1000 Midwest Parts
1000 Midwest Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


3000 Siemens Parts
3000 Siemens Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


350000 RPM Abu Parts
350000 RPM Abu Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


4000 MS-ML Siemens Parts
4000 MS-ML Siemens Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


4000 S-SL Push Button Siemens Parts
4000 S-SL Push Button Siemens Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


5000 - 5100 Adec Parts
5000 - 5100 Adec Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


8000 - 8000i Midwest Parts
8000 - 8000i Midwest Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


EM3000 Nose Cone C. De Giorgi Parts
EM3000 Nose Cone C. De Giorgi Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


7000 Abu Garcia Parts
7000 Abu Garcia Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


AR2000 Daiwa Parts
AR2000 Daiwa Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


DA4000M Daiwa Parts
DA4000M Daiwa Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


HA6000A Reelemin Parts
HA6000A Reelemin Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


BSR-1000 Belt Sander Ozito Parts
BSR-1000 Belt Sander Ozito Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


S 12000 RPM Sirona Parts
S 12000 RPM Sirona Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Stradic 4000 FI Shimano Parts
Stradic 4000 FI Shimano Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Theory 4000 Daiwa Parts
Theory 4000 Daiwa Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Straight Handpiece 6000 RPM W.H. Parts
Straight Handpiece 6000 RPM W.H. Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Belts - Timing - 10.000mm Pitch - AT10 - 10mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 10mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 12mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 12mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 16mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 16mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 20mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 20mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 25mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 25mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 32mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 32mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 10.000mm Pitch - AT10 - 50mm Wide
Belts - Timing - 10.000mm Pitch - AT10 - 50mm Wide

Also see combined categories:
All 10mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 5.000mm Pitch - AT5 - 10mm Wide
Belts - Timing -  5.000mm Pitch - AT5 - 10mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 5.000mm Pitch - AT5 - 12mm Wide
Belts - Timing -  5.000mm Pitch - AT5 - 12mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.

Related Information:


Belts - Timing - 5.000mm Pitch - AT5 - 16mm Wide
Belts - Timing -  5.000mm Pitch - AT5 - 16mm Wide

Also see combined categories:
All 5mm Pitch Timing Belts

AT Synchroflex Generation III Series Metric Timing Belts.

Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2320 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2320 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.