Small Parts & Bearings - an MBA company

CX75 TOTALOMNIFORCE


Cross Referenced Part Numbers



BV22-01905-CX75 Total Omniforce part number CX75





Inside Circumference: 1905.0 (75.0 in.). -: -. -: -.

Online Price: 0.00     
Stock: Pre-Order (due 3 weeks)     
Due dates are estimates only     


Category Matches

Gearboxes Cross Axis


Gearboxes - Cross Axis - 90 x 75 x 32mm
Gearboxes - Cross Axis -  90 x  75 x  32mm

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Related Information:


You may also be interested in

Bushes Plastic


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Vee Belts


Belts - Vee - 22.2 x 13.5mm - Notched CX
Belts - Vee - 22.2 x 13.5mm - Notched CX

Also see combined categories:
All Vee Belts 22mm and 22.2mm Top Width

22.2mm Top Width x 13.5mm Height.


Related Information:


757 Lares Parts
757 Lares Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


5177597 GE Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x 75.0 x 44.0mm
Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x  75.0 x 44.0mm

Also see combined categories:
All Right Angle Gearboxes

BLH40 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore
Sprockets -  3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Miniature 3.75mm Pitch.

Match with 3.75mm simplex chain. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Bushes - Plastic - Rulon J - Flanged
Bushes - Plastic - Rulon J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Bushes - Plastic - Rulon J - Unflanged
Bushes - Plastic - Rulon J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Max Load: 5.2 MPa (750 psi). Gold colour. Max surface speed: 2m/s. Max PV: 0.26 (Mpa x m/s)

Non Metallic Bushes. Excellent insulator. Nor suitable for steam or wet conditions. Not FDA compliant. Suitable for dry conditions or vacuum. 288 oC (550 Deg F) Maximum Working Temperature. Patented all polymeric PTFE compound which operates well against soft mating surfaces. Lowest co-efficient of friction in the Rulon(R) product range.

Related Information:


Gears - Spur - Module 0.75 - Brass
Gears - Spur - Module 0.75 - Brass


PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.


Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. For easy ready selected sets of chain and sprockets please see the HES website.

Related Information:


Gear Racks - Flexible
Gear Racks - Flexible

Also see combined categories:
All Flexible Gear Racks

Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.

20o Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.


Pins - Coiled - Plain - Standard Duty
Pins - Coiled - Plain - Standard Duty

Also see combined categories:
All Coiled Pins

ASME B18.8.3M / ISO 8750 Standard Duty Spirol Pins. Coiled roll pin.


Related Information:


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves


0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:


Rollers - Feed - With Aluminium Sleeve
Rollers - Feed - With Aluminium Sleeve

Also see combined categories:
All Rollers

Tolerance of Roller Outside Diameter (D) is +/-0.075 mm

Urethane 60 Durometer ground outside diameter. Aluminium sleeve. Feed rollers do not have a rotating bore. They are designed to turn with the shaft.

Related Information:


Sprockets - Idler
Sprockets - Idler


Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.

Related Information:


Gears - Spur - 8DP - 14.5 Degree - Steel
Gears - Spur -   8DP - 14.5 Degree - Steel

Also see combined categories:
All 8DP Spur Gears

PCD = No. of Teeth x 3.175mm (1/8 in.). 14.5o Pressure Angle. Steel. DP stands for Diametrical Pitch and is an imperial measurement system.

8 Diametrical Pitch. Approx 9.98mm between teeth.


RC Spare Parts - E-Flite
RC Spare Parts - E-Flite


E-Flite helicopter and Plane spare parts listed by description. Includes parts for Aprentice, MSR, Micro MCX, Blade 400 and CX2, CX3, T28D Trojan, Messerschmitt, AT6 Texan, SR120, Pawnee, Ultimate FX



Belts - Timing - 9.525mm Pitch - L - 12.7mm Wide
Belts - Timing -  9.525mm Pitch - L -  12.7mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 9.525mm Pitch - L - 19.1mm Wide
Belts - Timing -  9.525mm Pitch - L -  19.1mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 9.525mm Pitch - L - 25.4mm Wide
Belts - Timing -  9.525mm Pitch - L -  25.4mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Washers - Disc Spring - Ball Bearing Type
Washers - Disc Spring - Ball Bearing Type

Also see combined categories:
All Disc Springs

Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093 and belleville washers to DIN 6796.

Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown.


Belts - Timing - 9.525mm Pitch - L Double Sided - 12.7mm Wide
Belts - Timing -  9.525mm Pitch - L Double Sided - 12.7mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 9.525mm Pitch - L Double Sided - 19.1mm Wide
Belts - Timing -  9.525mm Pitch - L Double Sided - 19.1mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Belts - Timing - 9.525mm Pitch - L Double Sided - 25.4mm Wide
Belts - Timing -  9.525mm Pitch - L Double Sided - 25.4mm Wide

Also see combined categories:
All L 9.525mm Pitch Timing Belts

Standard Series Timing Belts 9.525mm or 0.375 inch pitch - Double Sided.

Pitch (P) - 9.525mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 4.60mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2321 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 128552 products in 2321 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.